manualshive.com logo in svg

Janome MC7700 QCP, Руководство по обслуживанию, Страница: 40 / 41

Поделиться
Скачать
Janome MC7700 QCP Скачать руководство пользователя страница 40

38

STEP 4 (SPEED CONTROL LEVER
AND FOOT CONTROL)

SLIDE VOLUME
[CORRECT CONDITION]
MOVE THE SPEED CONTROL
LEVER SLOWLY.
THE DISPLAY SHOWS WHEN THE
LEVER IS:
AT THE LEFT END:

000-008

AT THE RIGHT END:

1012-1024

FOOT CONTROL
[CORRECT CONDITION]
CONNECT THE FOOT CONTROL
TO THE MACHINE.
THE DISPLAY SHOWS WHEN
FOOT CONTROL IS:
RELEASED:

000–064

FULLY DEPRESSED:

832-955

DISCONNECTED:

956-1024

PRESS THE REVERSE STITCH
BUTTON TO PROCEED TO THE
NEXT STEP.

[FAULTY CONDITION]
THE DISPLAY DOES NOT CHANGE
OR INDICATES INCORRECT VALUE.

–REMEDY–
REPLACE THE SLIDE VOLUME,
FOOT CONTROL PLUG, CIRCUIT
BOARD A.

STEP 5
(THREAD TENSION  RELEASE
SOLENOID)

[CORRECT CONDITION]
THREAD THE MACHINE (NEEDLE
THREAD). LOWER THE PRESSER
FOOT. ADJUST THE THREAD
TENSION DIAL TO “9”.

PRESS THE CONFIRM BUTTON TO
RELEASE THE THREAD TENSION.
THE LCD WILL DISPLAY “ON”.
MAKE SURE THE THREAD CAN BE
PULLED WHEN THE BUTTON IS
PRESSED.
THE SOLENOID WILL BE OFF
AUTOMATICALLY AFTER 5
SECONDS.

PRESS THE REVERSE STITCH
BUTTON TO PROCEED TO THE
NEXT STEP.

[FAULTY CONDITION]
SOLENOID WILL NOT BE TURNED
ON OR THE THRAD CANNOT BE
PULLED WHEN THE CONFIRM
BUTTON IS PRESSED.

–REMEDY–
ADJUST THE SOLENOID
PLUNGER.

Содержание MC7700 QCP










































Отзывы:

Нет отзывов