manualshive.com logo in svg

Janome MC6600, Руководство по обслуживанию

Поделиться
Скачать
Janome MC6600 Скачать руководство пользователя страница 29

TO ADJUST UPPER FEED DOG (1)

TO CHECK

1. TURN THE POWER ON AND SELECT MODE 1.

SELECT STITCH #1 (     ).

2 PRESS THE STITCH LENGTH ADJUSTING KEY.

SET THE STITCH LENGTH TO ì0î. TURN THE

POWER OFF.

3 LOWER THE FEED DOGS.

4 REMOVE THE BASE.

5 CHECK IF THE BED AND UPPER FEED LOWER

SHAFT REAR ARM ARE PARALLEL.

ADJUSTMENT

6 SET THE UPPER FEED ADJUSTING DIAL TO 0.

7 LOOSEN THE SETSCREW SO THE CLEARANCE

BETWEEN THE UPPER FEED LINK SHAFT AND

UPPER FEED LOWER SHAFT SHOULD BE 2.5 MM.

8 ATTACH THE BASE.

THE CLEARANCE BETWEEN THE UPPER FEED LINK SHAFT AND UPPER FEED

LOWER SHAFT SHOULD BE 2.5 MM WHEN THE UPPER FEED ADJUSTING DIAL IS SET TO

“0”.

UPPER FEED DOG ADJUSTING DIAL

2.5mm

UPPER FEED LOWER SHAFT

REAR ARM

UPPER FEED

LINK SHAFT

UPPER FEED

LOWER SHAFT

UPPER FEED ADJUSTING

ARM (1)

BED

PARALELL TO

THE BED

2.5 MM

VIEW FROM THE BELT COVER SIDE

SETSCREW

27

2.5 MM

(GAUGE 846-G01)

Содержание MC6600


















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды