Janome JF1018S страница 19 Скачать руководство пользователя | Manualshive

Страница: 19 / 24

background image

17

BUTTONHOLE FEED BALANCE

Correct setting

When sewing buttonhole, the stitches on each side of buttonhole should be the same stitch
density.
The range of 9 -11 stitches in the right side row (backward feeding) against 10 stitches in
the left side row (forward feeding) is considered acceptable.

To adjust

1. Check the stitches by sewing buttonholes, and remove the cap.
2. Turn the adjusting screw in the direction of “C” in case of a (right stitches are coarse), or

in the direction of “D” in case of B (left stitches are coarse).

3. Attach the cap.

«
...
17
18
19
20
21
...
»

Содержание JF1018S

























Отзывы:

Нет отзывов

Похожие инструкции для JF1018S

Бренд: Fastbind Страницы: 4

Бренд: ELNA Страницы: 230

Бренд: Pure Fitness Страницы: 12

Бренд: Renown Страницы: 14

Бренд: Pfaff Страницы: 36

Бренд: Garudan Страницы: 67

Бренд: Singer Страницы: 25

PerfectCool Cielo

Бренд: IDROBASE Страницы: 16

Бренд: ZOJE Страницы: 100

Бренд: Sunny Health & Fitness Страницы: 10

Бренд: JUKI Страницы: 39

Бренд: Janome Страницы: 92

Бренд: KENT Страницы: 2

Бренд: Singer Страницы: 17

Бренд: Singer Страницы: 55

Бренд: Tornado Karcher Страницы: 53

Бренд: Performance Tool Страницы: 4

Бренд: Tema Telecomunicazioni Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды