Janome 3128 Скачать руководство пользователя страница 3

Страница: 3 / 23

MODEL 3128

CONDITION

CAUSE

HOW TO FIX

REFERENCE

1. Skipping

1. Needle is not inserted

Insert the needle properly.

properly.

stitches

2. Needle is bent or worn.

Change the needle.

3. Incorrectly threaded.

Rethread.

4. Needle or thread are

Use the recommended sewing

inappropriate for fabric

needle and thread.

being sewn.

5. Sewing on stretch fabric.

Use a #11 blue tip needle.

6. Inappropriate needle bar

See mechanical adjustment

P.15

height.

“Needle bar height.”

7. Inappropriate needle to

See mechanical adjustment

P.16

hook timing.

“Needle timing to shuttle.”

8. Inappropriate needle to

See mechanical adjustment

P.12,13

hook clearance.

“Clearance between needle

and hook.”

2. Fabric not

1. Incorrect feed dog height.

See mechanical adjustment

P.14

moving

“Feed dog height.”

2. Thread on bottom side of

Make sure to bring both needle

fabric is jammed up.

and bobbin threads under the

foot when starting sewing.

3. Feed dog teeth are worn.

Change the feed dog.

WHAT TO DO WHEN

Содержание 3128
























Результаты поиска

Содержание 3128

Отзывы:

Похожие инструкции для 3128

Бренды по названию

Популярные бренды

Janome 3128, Руководство по обслуживанию

Результаты поиска

Содержание 3128

Отзывы:

Похожие инструкции для 3128

Бренды по названию

Популярные бренды