background image

Prophi

®

 6R

12

13  ALARM TEMP

[ 50...85]°C

The  alarm  temperature  programmed  here  is  the  temperature  at  which  the 

capacitor  stages  are  disconnected  in  steps.  The  controller’s 

alarm  relay

 

responds after ten minutes. At the same time the display shows the cause of the 

alarm  (over-temperature).  If  the  temperature  drops  again,  the  required 

branches are automatically re-connected in steps. 

The selection is performed with the 

é

 /

ê

 keys. Save and continue with ENTER.

14  MESSAGE RELAY

this item appears if in ExpertMode2 the „alarm-relay“ is set as „message-relay“ 

The message relay can be programmed for 

one 

of the following options as 

required:

"Fan”

:

Relay switches the external cabinet fan.

(Default)

The switching threshold can be programmed under point 15.

Display: 

"F”

"Supply"

Message when active power is supplied. Display: 

"S”

"Undercurrent”

This  message  appears  whenever  the  measuring  current  is  not 

reached. Display: 

"U”

   The signal is generated when the value drops 

below the response sensitivity of the controller.

"Harmonics”

: This message appears when the limit of the total harmonic distortion 

THD-V is exceeded. This value can be set under "27 Harmonics” in%

15  FAN TEMP*

[15...70]°C

Input of the switching threshold for the fan. 

BASIC SETTING:

[ NO ]

( YES / NO )

When the selection is made with YES and confirmed with ENTER, all parameters 

are reset to the basic setting made by the PFC-system  manufacturer. 

(Optimal network values when the controller was supplied with a complete PFC-

system). If the controller is supplied from the works, this point corresponds to 

the default setting. 

CAUTION: All user settings are lost!

5.3  Programming  lock

(active / inactive / automatic after 24 h)

The device is equipped with a programming lock to ensure protection from unauthorized 

or inadvertent changes to the system parameters. The lock can be activated in expert 

mode.  If the lock is active, all parameters can be checked but not changed. 

* Only active

 if

 option 'Fan' is selected 

27  HARMONICS (harmonic limit)

[7]%

(0.5 ... 25,5)%

A limit for the total harmonic distortion THD-V (in%) can be entered here. When 

this  threshold  is  exceeded,  a  message  is  given.  THD-V  is  the  ratio  of  the 

geometric  sum  of  the  uneven  harmonics  to  the  fundamental.  A  warning  is 

always  shown in the display; an output via message relay only takes place 

when this was selected in point 14.

- 12 -

Содержание Prophi 6R





























Отзывы: