Jandy WaterColors LED, Руководство по установке

Страница: 9 / 20

Page 9
Section 5. Wiring Options for
Controlling Jandy
WaterColors LED Lights
NOTE The Jandy WaterColors Lights will not
operate properly with light dimmers. Do not wire
the Jandy Lights to any dimming circuitry .
To the extent allowed by code and capacity of the To the extent allowed by code and capacity of the
electrical equipment, multiple Jandy lights may be
electrical equipment, multiple Jandy lights may be
controlled with a single switch so their colors will
controlled with a single switch so their colors will
always always be synchronized. be synchronized.
Separate switches may be used to control the on/off and Separate switches may be used to control the on/off and
color functions of each Jandy light. It is recommended
color functions of each Jandy light. It is recommended
that these switches be located next to each other to
that these switches be located next to each other to
facilitate simple color synchronization when desired.
facilitate simple color synchronization when desired.
All switches
All switches must be operated at the same time to must be operated at the same time to
assure color synchronization. assure color synchronization. Otherwise, the lights will Otherwise, the lights will
work independently of each other. work independently of each other.
5.1 Wiring to an AquaLink
®
RS Control
System
The Jandy WaterColors Lights can be wired into
the Jandy AquaLink RS control system to provide
simpli
fi ed operation of the lights, as well as a means
to synchronize the color change function. Connect the
lights to one of the auxiliary relays in the Power Center.
NOTE It is recommended to connect one light per
relay so each light can be controlled separately.
However, up to four lights can be connected on
a single relay. If there are more than four lights
installed on one AquaLink RS system, ensure
there is more than one auxiliary relay available
in the Power Center.
Refer to Figures 2 and 3 to connect the Jandy Color
Lights to the Power Center.
CAUTION
A Ground Fault Circuit Interrupter (GFCI) must be
provided for 120 volt models. The conductors on the
load side of the GFCI circuit shall not occupy conduit,
boxes, or enclosures containing other conductors
unless the additional conductors are also protected
by a GFCI. Refer to local codes for complete details.
NOTE The Jandy WaterColors Lights are available
in 120-volt and 12-volt versions. If installing a
12-volt light, a 120-volt/12-volt step-down (AC)
transformer
must be used. For more information
about 12-volt installations, refer to Section 8 of
this manual.
5.2 Wiring to a Time Clock
The Jandy WaterColors Lights can be wired into a
basic time clock to automatically turn on the lights at
a predesignated time. Refer to Figure 4 to connect the
lights into the time clock.
5.3 Wiring to a Switch
The Jandy WaterColors Lights can be wired into a
switch to manually turn on/off the lights. Refer to
Figure 5 to connect the lights into the switch.
Section 6. Jandy WaterColors
LED Light Operating
Instructions
6.1 To Operate the Light and Change
Colors
Turn the light ON . The fi rst time the light is turned on,
the color sequence begins with the Alpine White. To
change the color, turn the light OFF and then ON within
three (3) seconds. Continue turning OFF and ON until
the desired light color mode is reached. See Table 1 for
the color mode sequence.
Table 1. Jandy WaterColors Lights Sequence
Sequence Order Color Modes
1 Alpine White
2 Sky Blue
3 Cobalt Blue
4 Caribbean Blue
5 Spring Green
6 Emerald Green
7 Emerald Rose
8 Magenta
9 Violet
10 Slow Color Splash
11 Fast Color Splash
12 America the Beautiful
13 Fat Tuesday
14 Disco Tech
NOTE When the light is turned OFF for more than
seven (7) seconds, it will remain in the color set
that is currently active. When the light is turned
back ON, the light will be on the same color set.