Jandy WaterColors LED, Руководство по установке

Страница: 13 / 20

Page 13
WARNING
Risk of Electrical Shock or Electrocution. Always
install a new lens gasket whenever disassembling
the light (Jandy Color Light Gasket P/N R0451101 for
large light and P/N R0400501 for small light). Failure
to do so may permit water to leak into the assembly,
which could cause:
(a) An electrical hazard resulting in death or serious
injury to pool or spa users, installers, or others due to
electrical shock, or
(b) A malfunction of the Jandy WaterColors Light,
which likewise could result in serious injury to pool or
spa users, installers, or bystanders, or in damage to
property.
b. While holding the fixture upright, place the glass b. While holding the fixture upright, place the glass
lens with the gasket on top of the fixture. Please lens with the gasket on top of the fixture. Please
note that the lens gasket is not symmetrical.
note that the lens gasket is not symmetrical.
Therefore, it must be installed correctly so that
Therefore, it must be installed correctly so that
the lens can seal to the fixture housing. Place the
the lens can seal to the fixture housing. Place the
gasket on the lens so that the thick molded side
gasket on the lens so that the thick molded side
of the gasket will mate with the housing when the
of the gasket will mate with the housing when the
lens is installed.
lens is installed. See Figure 10. On the small light, See Figure 10. On the small light,
replace the diverger by tucking the tabs between replace the diverger by tucking the tabs between
the lens and gasket.
the lens and gasket.
NOTE Be sure to face the dull side of the diverger
down towards the PCB.
c. Position the lens and gasket on the fixture. Place c. Position the lens and gasket on the fixture. Place
the face ring assembly over the lens and align the the face ring assembly over the lens and align the
pilot screw with the small arrow mark on the face
pilot screw with the small arrow mark on the face
of the lens. Note that the small arrow mark on the
of the lens. Note that the small arrow mark on the
face of the lens and the pilot screw of the face ring
face of the lens and the pilot screw of the face ring
must be aligned with the arrow located on fixture
must be aligned with the arrow located on fixture
label that reads, “Arrow on this label must line up
label that reads, “Arrow on this label must line up
with the pilot screw on the Face Ring”. See
with the pilot screw on the Face Ring”. See
Figure 9.
Figure 9.
d. While holding the aligned face ring assembly and d. While holding the aligned face ring assembly and
fixture together, turn the assembly upside down fixture together, turn the assembly upside down
and set it on the old gasket, using the old gasket
and set it on the old gasket, using the old gasket
as an assembly fixture. This will keep the lens and
as an assembly fixture. This will keep the lens and
gasket assembly from being pushed out of the face
gasket assembly from being pushed out of the face
ring while you secure it to the light fixture.
ring while you secure it to the light fixture.
e. Spread the bottom clamp over the electrical cord e. Spread the bottom clamp over the electrical cord
and slide it onto the back of fixture to the top and slide it onto the back of fixture to the top
clamp.
clamp.
f. Tighten the Phillips head screws (eight (8) for f. Tighten the Phillips head screws (eight (8) for
large light and six (6) for small light) on the light large light and six (6) for small light) on the light
in alternating cross-pattern. Torque screws to
in alternating cross-pattern. Torque screws to
approximately 20 in-lbs. Do not over-tighten.
approximately 20 in-lbs. Do not over-tighten.
g. Discard the old gasket. g. Discard the old gasket.
Figure 7. Small Light Engine (PCB) Replacement
and Wiring
AC1 AC2
Black (12V)
Blue (120V) White (12V)
Red (120V)
Green
Nylon
Washer
Nut
Light
Engine
Secure
First
120V Wiring 12V Wiring
White
Green
Black
J6
J2
J3
J2
White
Green
Black
Nylon
Washer
Nut
Nut
Secure
First Secure
First
Figure 8. Large Light Engine (PCB) Replacement and Wiring