background image

Jandy Ray-Vac

®

SECTION 2.
General  Information

2A.   Introduction

       

   The Jandy Ray-Vac

®

 automatic pool cleaner is

designed to both vacuum and sweep your swimming
pool. The cleaner head moves in a random submerged
pattern about the pool, traveling, vacuuming and
cleaning from the pool floor to the water line. Its pattern
is determined by the shape of the pool, the
hydrodynamics of the cleaner design, adjustments of the
water pressure, and the forward and backward motion
created by the patented backup jet system.

The pool cleaner, by the use of its large suction

mouth, will vacuum dirt, leaves, and debris and store it
in its own chamber located in the cleaner head. In
addition, its drive jets are angled slightly downward
creating a powerful jet action to sweep any small debris
down to the main drain where it is removed by the filter
system.

In most typical residential pools, the pool cleaner

will eliminate 90% or more of the manual labor
involved in cleaning the pool. Because many of the
factors present in a swimming pool, such as shape of the
pool, location of the return lines, mounting point of the
cleaner, etc., there may be small areas where dirt tends
to collect. Usually, these areas are small and are
considered normal.

SECTION 3.
Emptying the Ray-Vac

3A. Emptying the Debris Chamber

1.

To prevent the cleaner from losing debris, leave
the pump(s) on (filter or booster pump) and direct
the cleaner towards the edge of the pool.

2.

Grab the cleaner by the nose wheel and lift it out
of the pool (direct water coming from cleaner
toward the pool. See Fig 1).

Page 2

3.

Place the Ray-Vac on its back. Locate the two (2)
debris compartment latches. Rotate latch to open
position (see Fig 2).

4.

While holding the Ray-Vac head down, firmly
grasp debris compartment cover. Pull the debris
compartment cover up and away from the tail
section to remove (see Fig 3).

5.

Pull the screen up and away from the tail section
to remove (see Fig 4).

Figure 1. Remove Ray-Vac from Pool

Figure 4. Remove Debris Compartment Screen

Debris Compartment

Screen

Figure 3. Remove Debris compartment

Debris Compartment

Figure 2. Open Debris Compartment Latches

Debris Compartment

Latches

Содержание JANDY RAY-VAC H0555100

















Отзывы: