Jandy CS100 Скачать руководство пользователя страница 7

Page

Cartridge Filters - CS Series Filter

Never exceed the manufacturer's maximum 

recommended filter flow rates.

5.  For best efficiency use the fewest possible number 

of fittings. This will prevent a restriction of the 

water flow.

6.  Make all plumbing connections in accordance with 

local plumbing and building codes. Filter unions 

are provided with an o-ring seal. Use silicone 

based lubricants on the o-rings to avoid damage. 

Do not use pipe joint compound, glue or solvent 

on union threads.

7.  Keep piping tight and free of leaks. Pump suction 

line leaks may cause air to be entrapped in filter 

tank or loss of prime at the pump. Pump discharge 

line leaks may show up as equipment pad leaks or 

air being discharged through the return lines.

8.  Support the inlet/outlet pipes independently to 

prevent any undue strains.

9.  Place the union nut over the pipe and connect 

the pipes to the union tailpieces using PVC 

glue. Do not use teflon tape or pipe dope on any 

union threads. Put the o-ring in the tailpiece and 

assemble the unions to the filter tank.

10.  Drill pilot holes into the equipment pad with a ¼" 

masonry bit. Use the holes in the tank bottom base 

as a guide.

11.  Install ¼ x 2¼" Stainless Steel Tapcon® screws 

and tighten.

3.3  Filter Installation

1.  This filter operates under pressure. When the 

locking ring is properly seated and the filter is 

operated without air in the water system, this filter 

will operate in a safe manner.

2.  If the system can be subjected to higher pressures 

than the maximum working pressure of the lowest 

rated component, install an ASME approved 

automatic Pressure Relief Valve or Pressure 

Regulator in the circulation system.

3.  Place the filter on the concrete pad, lined up with 

the inlet and outlet pipes.

4.  To reduce pressure losses, 2" (minimum) piping 

is recommended for plumbing the system. 

Figure .  Pressure Gauge and Pressure Release 

Assembly

Air Release

Valve

Pressure

Gauge

Pressure

Gauge

Adapter

Figure 5.  Basic Pool/Spa Combination Plumbing

Jandy Heater

Waterfall

Pool Return

Spa Make Up

Spa Return

From Pool Skimmer

From Pool 

Drain

Spa Suction

Jandy Pump

Jandy

Check

Valve

Outlet  

Port

Inlet Port

Jandy Filter

Inlet  

Port

Drain

Содержание CS100

















Отзывы: