manualshive.com logo in svg

Jandy CS100, Инструкция по установке и эксплуатации, Страница: 11 / 16

Поделиться
Скачать
Jandy CS100 Скачать руководство пользователя страница 11

Page 11

Cartridge Filters - CS Series Filter

7.  If the obstruction or debris can not be removed 

or the breather tube is damaged, 

STOP

 using the 

filter immediately and replace the breather tube 

assembly.

8.  Reassemble breather tube.  Fully seat the breather 

tube into the bottom tank.

9.  Replace the filter locking ring/tank top assembly 

on the filter and tighten (See Section 3.4 "Locking 

Ring/Tank Top Assembly Installation").

10.  Reopen isolation valve if they were closed.
11.  Stand clear of the filter, start the pump and 

circulate the water until water sprays out of the air 

release valve. Close the air release valve. The filter 

is now back in operating mode.

12.  Watch the pressure gauge to be sure that the 

pressure does not exceed 50 psi. If the pressure 

approaches 50 psi, immediately turn the pump 

off and clean the filter cartridges. If the pressure 

remains high after cleaning the filter, refer to the 

troubleshooting guide, Section 8, for possible 

causes and solutions.

Section 7.  Winterizing

1.  Turn 

off

 the filter pump and switch off the circuit 

breaker to the pump motor.

2.  Open air release valve on top of the filter. 

Do not 

remove.

3.  Loosen the drain nut and cap at the base of the 

filter to ensure that the tank is empty. 

4.  Drain circulation system of all water.
5.  Cover the system with a tarpaulin or plastic sheet 

to protect it from the weather.

          WARNING

If the breather tube is not fully seated or 

is damaged or clogged, trapped air can 

cause the filter lid to be blown off which 

can result in death, serious personal 

injury or property damage.

Содержание CS100

















Отзывы:

Нет отзывов