J&M 375ST Speed Tender Скачать руководство пользователя страница 60

Страница: 60 / 62

Slide the weigh bar into the scale mount. Making sure that the Weigh bar sticker is facing up (Figure 6.1).

Insert two 3/8”-16 X 3 1/2” Grade 5 Zinc Hex Bolt (#1) into scale mount and tighten using 3/8”-16 Centerlock Hex Nut

(#2) (Figure 6.1).

Insert 4 Spacer Blocks in between the Shell/Leg Weldment and the Chassis Frame. Be sure the 4 Spacer Blocks are

identical in width and fit snug between the Shell/Leg Weldment and the Chassis Frame (Figure 6.2).

Remove the 4 bolts from each of the Dummy Scale Mounts and remove it from the unit.

WARNING: With the 4 bolts removed from each of the Dummy Scale Mounts. The Chassis and Shell are not attached and

can slide apart.

Lift the shell approximately 2-3”. This will allow enough clearance to slide the weigh bars into the Shell/Leg

Weldment Spools. (Figure 6.2).

Slide Weigh Bars into the Shell/Leg Weldment Spools and lower the Shell/Leg Weldment down so the Weigh Bar Mounts

set on the Scale Mounting Plates.

Use a punch to align the Weigh Bar Mount holes with the Scale Mounting Plate holes.

Insert 1/2”-13 X 1 3/4” Grade 5 Hex Head Bolt (#3) with two 1/2” Zinc USS Washers (#4) and 1/2”-13 Grade 5 Zinc

Centerlock Hex Nut (#5) (Figure 6.3)

IMPORTANT: Be careful not to pinch wires between the Speed Tender chassis and the Scale Mounting Plates.

Torque each bolt down to 85 ft-lbs on all 4 Scale Mounting plates (Figure 6.3).

6.0 Aftermarket Installation Instructions

6.1 Scales Installation

Note: For Scale parts see Section 5.3

Figure 6.1

Figure 6.2

Figure 6.3

Spacer Block

Shell/Leg

Weldment Spools

Содержание 375ST Speed Tender































































Результаты поиска

Содержание 375ST Speed Tender

Отзывы:

Похожие инструкции для 375ST Speed Tender

Бренды по названию

Популярные бренды

J&M 375ST Speed Tender, Руководство оператора

Результаты поиска

Содержание 375ST Speed Tender

Отзывы:

Похожие инструкции для 375ST Speed Tender

Бренды по названию

Популярные бренды