background image

Damper Door Striker Plates Installation:

• On the edge of the housing venturi under the just placed rubber gasket 

   locate the 4 striker plate grooves nearest the center of the fan venturi,

   (

do no

t use the ones nearest the top or the bottom of the fan).

• Carefully lift off the rubber gasket over the striker plate groove and insert 

   (1) SS 

Damper Door 

Striker Plates from Bag 9 (Misc. Hardware)

   at each location, angle the striker plate so the angle matches the fan 

   housing. To secure the striker plates, press the rubber gasket back down.

NOTE: 

No hardware is used to secure striker plates at this time.

11

Rubber Gasket Installation:

• Peel the backing off the rubber gasket 1’ at a time and with the raised 

   portion to the center and flush to the interior of the venturi stick it to 

   the housing.
• Continue to stick the gasket around the entire circumference of the 

   housing opening. 
• When you are back to the starting point cut off any excess gasket. 

   Stick it down lining up the two ends of the gaskets.
• Go back and press down on the flat part of the gasket all the way 

   around the housing to make sure it is stuck down. 

10

Cone Assembly:

• Lay out the (8) cone pieces, place the (2) sections with the J&D logo 

   across from each other as shown below.
• Using 

(6) 5/16”-18 x 7/8” 

Bolts from Bag 5 (Part 2) 

and (6) 5/16”-18 

   Serrated Flange 

Nuts from Bag 5 (Part 3)

, assemble two cone pieces. 

   Repeat until all (8) cone pieces are assembled.
• Using a 1/2” socket with impact driver and wrench tighten the cone 

   pieces together.

12

IS295-20H  

 

J&D Manufacturing • 6200 Hwy 12 • Eau Claire, WI 54701 • 1-800-998-2398 • www.jdmfg.com 

Page 7/12

Cut away view

Top

of

Fan

Содержание MAGNUM 58"













Отзывы: