background image

3030 not working? - see the trouble shooting guide on page 9

Occasionally clean top and bottom heat plates with a solvent such
as J&A Superspray and a clean, dry cloth.

Regularly check that the temperature between the heat plates is the
same as is reading on the display. To measure the inter-plate
temperature you will require a digital thermometer fitted with a thin
thermocouple.

PROCEDURE

Set the dwell time to 60 seconds.
Place a thermocouple between the plates and pull down head.
The thermometer reading will rapidly rise and then level out.
If the reading is still rising at the end of the 60 second dwell
period simply repeat until it does level out. The temperature
indicated on the thermometer should be /- 3˚C of the
set temperature. If not, calibrate the machine as below.

CALIBRATION

Carry out the test above to determine if machine needs calibrating.

In order to access the ‘temperature adjust’ mode a four digit
password must be entered to match the password set by the
manufacturer at “0101”. Change the display by pressing
the

4

button until the following screen appears: 

The ‘<’ symbol indicates that the right hand two of the four digits
may be adjusted by using the 

5

and 

6

buttons.

Then press the

4

button to change the display to: 

Indicating that the left hand two of the four digits may
be adjusted using the 

and 

6

buttons. 

Enter the password 0101 and wait for about 10 seconds.
The display will then change to: 

The

4

button may  now  be  used to advance to a previously

unavailable screen showing: 

This screen is displaying the temperature between the plates and
can be adjusted to read the same as the thermocouple by using the

5

and 

6

buttons. 

Once the temperature has been calibrated the ‘Gain adjust’ screen
may be disabled again by simply reverting to the password screen
and altering the displayed digits to be anything other then the
password (0101).

8

ROUTINE MAINTENANCE 

COUNT nnnn 

PASSWORD 0000< 

COUNT nnnn 

PASSWORD >0001

COUNT nnnn 

PASSWORD XXXX 

GAIN ADJUST

nnnC

Representation
of display screen

Representation
of display screen

Representation
of display screen

Representation
of display screen

 

Содержание 3030
















Отзывы: