background image

SETTING GUIDE

FRONT CAMBER ANGLE SETTING

REAR CAMBER ANGLE SETTING

Place the model car on flat surface. Raise the chassis to it's maximum clearance
before the wheels leave the ground.
Adjust the length of the front and rear upper arms so that the wheels are right angle to the
ground.
The camber angle adjustment can be moving the turnbuckle rod on the upper arms, 
clockwise or anti-clockwise.

(We suggest use zero degree for the front and 1.5

degree  for the  rear.) 

 negative 

-

-

-

-

+

+

+

+

Turnbuckle

Turnbuckle

FRONT TOE-IN AND TOE-OUT SETTING

TOE-IN

TOE-OUT

NEUTRAL POSITION

Making the tie rod shorter will make  the front tires 
become toe-out.
Response will be quicker and will under steer.   

REAR SHOCK ANGLE SETTING

    1  2 3

1 2

Firm rear suspension, over steering.
Soft rear suspension, under steering.  

Steering Rod

FRONT SHOCK ANGLE SETTING

Firm front suspension, less steering.
Soft front suspension, more steering.

123

Soft

Soft

Soft

Firm

Firm

Firm

Negative

Negative

Positive

Positive

Adjust  the  length of front steering  rod to change the
toe angle.

Making the tie rod longer will make the front tires 
become toe-in.
Response will be slower and will over steer. 

  4 

  5 

3

1 2

Soft

Firm

3

TOE-OUT

Adjust the front caster angle by changing the arm block "A" or "B" on the front lower arms. 
After you set the caster angle , you will also need to adjust the front upper arm position. 
The final caster also depends on the kick-up setting. 
Example:15 degree caster on C-hub + 7degree kick-up+"A" lower arm block =22 degree  final caster.
                  15 degree caster on C-hub + 7degree kick-up+"B" lower arm block =20 degree  final caster 
                 

Caster angle       

                           

Characteristics

                                     Increases off-power steering into a corner.
Less caster                Decreases on-power steering out of and in a corner.
                                     Decreases straight-line stability.

                                     Decreases off-power steering into a corner.
More caster               Increases on-power steering out of and in a corner.
                                     Increases straight-line stability.

CASTER ANGLE

A

A

B

B

7 degree

15 degree
on C hub

REAR WHEELBASE

0

367.5mm 370mm

365mm

Adjust the wheelbase by using the spacers on either side of the rear uprights (at the bottom pin).

 

less spacers in front of the rear upright.
- increases rearward weight transfer during acceleration.
- increases on-power traction.
- quicker off-power steering into corners.
- slight tendency to push on-power at corner exit.
- increases steering response.
- better on tighter, more technical tracks.

 

more spacers in front of the rear upright.
- decreases off-power steering into sharp corners.
- increases stability.
- slower initial steering reaction (off-power).
- improves on-power steering at corner exit.
- better handling over bumps and ruts.
- better on more open tracks with high-speed corners.

IMPORTANT! Make equal adjustments on both left and right sides of the car.

Shorter wheelbase

Longer wheelbase

20

Содержание X1 CRT 2005 ROAR National Champion







































Отзывы: