JAI CM-140GE Скачать руководство пользователя страница 42

Страница: 42 / 76

CM-140GE / -RA/-UV / CB-140GE / -RA

- 40 -

10. Operation Modes

The CM-140GE and CB-140GE series comply with GenICam SFNC (Standard Features Naming

Convention) version 1.3 and the acquisition of the image, the trigger functions, the exposure

settings and so on are different from those used in early versions of these cameras.

Note: In this section, the GUI shown is from the CB-200GE.

10.1. The functions related to GenICam SFNC 1.3

The following functions are the most affected by SFNC 1.3.

Features – Acquisition and Trigger Control

Acquisition mode

The image can be captured in two ways, continuous or single fame.



Continuous

By executing AcquisitionStart command, the image can be output until AcqusitionStop Trigger is

input.



Single Frame

By executing AcquisitionStart command, one frame of the image can be output and then the

acquisition is stopped.

Trigger Selector

This can be selected from FrameStart or TransferStart.



FrameStart

The trigger pulse can take one frame capture.



TransferStart

The trigger pulse can read out the image stored in the frame memory. This is used for the

delayed Readout

TriggerMode

This selects either trigger mode (ON) or continuous mode (OFF).

TriggerSoftware

This is one of the trigger sources which enables trigger commands to be created using software.

In order to use TriggerSoftware, TriggerSource should be set at Software.

TriggerSource

The trigger source can be selected from the following signals.

Содержание CM-140GE













































































Результаты поиска

Содержание CM-140GE

Отзывы:

Похожие инструкции для CM-140GE

Бренды по названию

Популярные бренды

JAI CM-140GE, Руководство пользователя

Результаты поиска

Содержание CM-140GE

Отзывы:

Похожие инструкции для CM-140GE

Бренды по названию

Популярные бренды