JAI CM-140GE Скачать руководство пользователя страница 41

Страница: 41 / 76

CM-140 GE / -RA/-UV / CB-140GE/-RA

- 39 -

9.3. Auto-detect LVAL-sync / async. accumulation

This function replaces the manual setting found in older JAI cameras. Whether accumulation is

synchronous or asynchronous in relationship to LVAL depends on the timing of the trigger input.

When trigger is received while FVAL is high (during readout), the camera works in LVAL-

synchronous mode, preventing reset feed through in the video signal. There is a maximum jitter of

one LVAL period from issuing a trigger and accumulation start.

If trigger is received when FVAL is low, the cameras works in LVAL-asynchronous (no delay) mode.

This applies to both pre-select (PS) trigger mode and pulse width (PW) trigger mode.

Ext. trigger

FVAL

(1)

(3)

(1) In this period camera executes trigger at next LVAL (prevents feed-through noise)

(2) Avoid trigger at FVAL transition (

+/- 1 LVAL period), as the function may randomly switch

between "next LVAL" and "immediate".

(3) In this period camera executes trigger immediately (no delay)

(2)

Fig. 27 Auto-detect LVAL sync /async accumulation

Содержание CM-140GE













































































Результаты поиска

Содержание CM-140GE

Отзывы:

Похожие инструкции для CM-140GE

Бренды по названию

Популярные бренды

JAI CM-140GE, Руководство пользователя

Результаты поиска

Содержание CM-140GE

Отзывы:

Похожие инструкции для CM-140GE

Бренды по названию

Популярные бренды