background image

Safety instructions

Item no. 15201035, Revision 01

8 ( 40 )

4.1

Safe working

Observe all safety instructions set out in the manual, the applicable national
accident prevention regulations, and the valid company work, operation, and
safety guidelines.

DANGER: Due to flying parts.

Tools  that  are  not  clamped  correctly  will  be  flung  away  by  the  centrifugal
forces that occur during machining.

u

Use the full clamping depth of the collet.

u

Clamp the tool securely.

DANGER: Due to flying parts.

If  the  wrong  rotational  direction  is  used,  the  clamping  system  releases  and
the tool is flung away.

u

It is essential to adhere to the rotational direction of the HF spindle.

WARNING: Risk of injury due to flying parts.

The  HF  spindle  operates  at  high  speeds  which  may  cause  chips  to  fly  out
with great force.

u

Never remove the protective devices of the machine or system.

u

Always wear protective goggles during work.

Example of design: Inserting the

shank

Note: Ensure functionality.

u

Never operate the HF spindle without a clamped tool shank.

If no tool shank is clamped:

q

The clamping system is damaged by the centrifugal forces.

q

The clamping system is shifted.

q

The balance of the HF spindle is affected.

q

The bearing is damaged.

Ü

Take the relevant measures to protect against splashes and spray accord-
ing to the type of machining, the type of material being machined, and the
type of tool selected.

Ä

Observe the manual of the machine in which the HF spindle is installed.

Ü

Obtain the maximum circumferential speeds of the tools used from the
tool supplier.

Single-point tools are not suitable for high speed cutting.

If they are required for production reasons:

Ü

Only use a balanced tool.

Ä

DIN ISO 1940

Ä

Balance grade 2,5

Содержание Z33-M080.03 K2S15









































Отзывы: