8
NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS MUST BE
PURCHASED SEPARATELY.
1 0 9 1 6 0
1 0 9 1 6 0
ROUGHING-IN DIMENSIONS
Plumbers' Putty or Caulking
Adjustable Wrench
Phillips Screwdriver
Channel Locks
TOOLS REQUIRED
Tubing Cutter
Regular Screwdriver
Basin Wrench
Turn off hot and cold water
supplies before beginning
CAUTION
1
INSTALL FITTING WITH OR WITHOUT ESCUTCHEON PLATE
When using the optional ESCUTCHEON PLATE (1) make sure the
O-RING (2) is against the sink and the ESCUTCHEON PLATE
ADAPTER (3) is under the ESCUTCHEON PLATE (1). Use
ESCUTCHEON MOUNTING KIT (4) to secure ESCUTCHEON
PLATE (1) to mounting surface. Mount Faucet onto ESCUTCHEON
PLATE (1) as detailed below.
Install the FAUCET SUPPLIES (5), SPRAY HOSE (6) and MOUNTING
SHANK (7) into the mounting hole in the sink, counter top or
ESCUTCHEON PLATE (1).
7
6
8
9
10
9
5
10" ESCUTCHEON
PLATE KIT
1
2
3
Connect the HOT water supply line to FLEXIBLE SUPPLY marked
with a
Red
tag. Connect the COLD water supply line to FLEXIBLE
SUPPLY marked with a
Blue
tag.
2b
WATER SUPPLY CONNECTIONS
INSTALL CHECK VALVE AND MAKE SPRAY HOSE CONNECTIONS
Use 1/2" IPS FLEXIBLE SUPPLIES (8) or 3/8" O.D. BULL-NOSE
RISERS (9) to connect to SUPPLY STOPS (10). Use adjustable
wrench to tighten connections. Do not over tighten. Be careful
not to kink copper supply when bending. Use tubing cutter to cut
to proper length.
2
RED
BLUE
Single Lever Pull Out
Spray Kitchen Faucet
Slide COUPLING NUT (1) of ADAPTER HOSE (2) onto end of
MOUNTING SHANK (3). Tighten with wrenches to make a
water tight connection.
Attach CHECK VALVE (4) to end of SPRAY HOSE (5).
Make sure rubber washer is installed into CHECK
VALVE (4). Install FIBER WASHER (6) into
COUPLING NUT (7) of ADAPTER HOSE (2).
Attach ADAPTER HOSE (2) to CHECK VALVE (4).
Tighten to make a water tight connection.
With HAND SPRAY seated in faucet body, install
WEIGHT (8) onto HOSE (5) using two SCREWS (9).
Locate the WEIGHT (8) two feet (2') from the underside
of the sink deck. Tighten SCREWS (9) firmly.
1
4
5
8
9
3
2
6
7
RUBBER
WASHER
BLUE
RED
FERRULE
SUPPLY STOPS
HOT
COLD
12
11
Assemble the two BRASS SCREWS (12) into the RETAINING LOCKNUT (11).
Assemble SUPPORT PLATE (8) with collar facing down onto SPOUT
SHANK (7). Assemble RUBBER WASHER (9) BRASS WASHER (10)
RETAINING LOCKNUT (11) onto SPOUT SHANK (7) from underside of
sink or countertop.
Align and center FAUCET. Tighten LOCKNUT (11) on SPOUT SHANK (7).
Tighten the two BRASS SCREWS (12) to secure FAUCET to mounting
surface.
1/2" NPT
8-3/16"
6-1/16"
2"
9-7/8"
1-9/16"
3-7/16"
6-7/8"
13-7/8"
2-3/8" D.
1-1/4" D.