background image

Installation Instructions

To ensure that your installation proceeds smoothly--please

read these instructions carefully before you begin.

  © J A D O   U S A   2 0 0 5

P r o d u c t s

L u x u r y   F a u c e t s   a n d   A c c e s s o r i e s

Product Numbers

Determine where the finished wall location will be. 

This measurement

is very important!  

Note: The rough-in measurement from the finished

wall is; 2" minimum and 2-3/4" maximum. This is a 3/4"

tolerance. See rough-in illustration above.   

Plumbers' Putty or Caulking

Teflon Sealing Tape

3/8" hex wrench

Adjustable Wrench

Phillips Screwdriver

TOOLS REQUIRED

Regular Screwdriver

3

INSTALL WALL SPOUT and HANDLE SUPPORTS

11 

10 

12 

1

8

13 

Remove PLASTER GUARDS and unthread ROUGH-IN NIPPLE (7).

Remove SET SCREW (1) from SPOUT (2) with 2.5mm HEX WRENCH (10) supplied.

Pull SPOUT ADAPTER (3) from SPOUT (2). Uthread SPOUT NIPPLE (4) from

SPOUT ADAPTER (3). 

Inspect that SPOUT NIPPLE O-RINGS (5 & 6) are seated in the grooves of SPOUT

NIPPLE (4). 

See View A.

Thread SPOUT NIPPLE (4) into VALVE BODY (11) and tighten using a 3/8" hex wrench.
Thread SPOUT ADAPTER (3) onto SPOUT NIPPLE (4) so that the face extends

1" beyond finished wall. 

See Figure "2"

.

Install ESCUTCHEON O-RING (8) in back of SPOUT ESCUTCHEON (9). Install the

SPOUT ESCUTCHEON (9) onto SPOUT (2).

Push SPOUT (2) onto SPOUT ADAPTER (3) and press tight against

finished wall. Align SPOUT (2) and tighten SPOUT SET

SCREW (1) with 2.5mm HEX WRENCH (10).

View A

View A

5

TEST INSTALLED FAUCET

Unthread SPOUT END and remove AERATOR.

Thread HANDLE SUPPORTS (12) onto

CARTRIDGE (13) and tighten with

adjustable wrench.

With HANDLES in OFF position, turn on

WATER SUPPLIES and check for leaks.

Operate both HANDLES to flush water

lines thoroughly.

Turn HANDLES off and replace AERATOR.

6

HELPFUL HINTS FOR CLEANING AND MAINTENANCE

The solid brass product you have just purchased has been designed to give you years of beauty and service. It is

important to bring to your attention proper care and maintenance procedures, which will ensure its lasting beauty.

First and foremost, it is important (as it is with any fine piece of jewelry or furniture) that the product be wiped clean and

dry with a soft damp cloth after every use.
Second, under no circumstances should an abrasive cleaner or combination cleaner/polish be used on JADO products.

The abrasive nature of such products will eventually destroy the finish and void the warranty.
In the event of stubborn blemishes shown on the finish, we recommend use of Windex window cleaner with a soft cloth,

but we do not recommend it be used on an everyday basis.

ROUGHING-IN

DIMENSIONS

Channel Locks

Wall Mount Vessel Faucet

H 9 6 5 5 7 8

H 9 6 5 5 7 8

H 9 6 5 5 7 8

H 9 6 5 5 7 8

JADO USA
6615 West Boston
Chandler, AZ 85226
Phone:(8OO) 227-2734
Fax: (8OO) 552-JADO(5236)
www.jadousa.com

TO THE PURCHASER OF JADO BRASS PRODUCTS

Attention installer:

Please leave This Pamphlet for The Owner

POLISHED BRASS AND CUSTOM FINISH WARRANTY

: A 1 YEAR LIMITED FINISH WARRANTY from date of purchase is provided to the

first residential owner against defects in materials and workmanship.  Due to the ever-changing finish of Patina products, the finish warranty

is excluded.  Warranty shall not include problems related to the installation of the product.

MECHANICS

MECHANICAL WARRANTY: 

A LIFETIME LIMITED WARRANTY is provided to the first residential owner on parts to be free from failure

related to defects in materials and workmanship but not installation.

CONDITIONS TO WARRANTIES

JADO Bathroom & Hardware Manufacturing Corp. places the following conditions on its finish and mechanical warranties to the first residential owner only.

JADO finish and mechanical warranties are limited to products correctly installed and used in a residential environment.

JADO warranties will not assume liability for damage due to abuse, mishandling, incorrect installation, improper maintenance, or deterioration

due to normal use.

JADO will not be liable for labor or other costs relating to the sale, installation, or replacement of their products.

In the  event of a defect in any JADO product covered by this warranty, the product must be returned to the dealer where originally purchased

along with proof of purchase.

JADO's obligation under the warranty shall be limited to the repair or exchange of any product which has been determined by JADO to be

defective after appropriate examination.

The  state  of  California  has  mandated  under  Proposition  #65  that 
manufactures  of  products,  including  faucets  which  come  into 
contact with potable water, must warn the consumer if the product 
contains  materials  listed  by  the  state  as  a  carcinogen  or 
reproductive toxin.  Lead, which is contained in all brass faucets in 
limited amounts appears on the State's list.

Preliminary  industry  tests  have  indicated  that  users  of  faucets 
made from brass face no significant danger, however,
California Proposition #65 requires that we  provide you with the 
following notice:

NOTICE:  JADO  products  conform  to  industry 
requirements  of  water  conservation  under  the 
ASTM  /  ANSI    A112.18.1M-1994    plumbing  code.   
Lavatory,  bidet,  wet  bar  and  kitchen  faucet  sets 
have  a  maximum  flow  rate  of  2.2GPM.    Shower 
heads,  hand  showers  and  body  sprays  have  a 
maximum flow rate of 2.5GPM.

Warning:  This product contains an element 

known to the State of California to cause cancer

of reproductive harm.

JADO BATHROOM AND HARDWARE MFG. CORP.

6615 West Boston

Chandler, AZ 85226

 

  JADO warrants this product to be free from defects in materials or workmanship for as long as the original consumer purchaser

owns their home.

  JADO will provide, free of charge, at it’s sole option, replacement part(s) or product (or if no longer available, a comparable

product) to replace those which have proven defective in materials or workmanship.

  Proof of purchase (original sales receipt) from the original consumer purchaser must be made available to JADO for all limited

warranty claims. This limited warranty is non transferable. It does not apply in the event of product damage due to the use of other than

genuine JADO replacement parts, installation error, abuse, misuse, or improper care and maintenance (whether performed by

a plumber, contractor, service provider or member of the purchaser’s household). The limited warranty excludes damage due to aggressive

air or water conditions, or harsh or abrasive cleaners and/or materials. This limited warranty excludes all industrial, commercial and business

usage, whose purchasers are hereby extended a two year limited warranty (with the exception of solenoid valves and other electronic

components which carry a one year limited warranty) applying to all other terms of this limited warranty except duration. This limited warranty

does not cover labor charges incurred and/or damages sustained in installation, repair or replacement, nor incidental or consequential

damages, all of which are expressly disclaimed. This limited warranty is applicable only to JADO faucets manufactured after June 1, 1996

and installed in the United States and/or Canada.

  This limited warranty gives the original consumer purchaser of an JADO faucet specific legal rights which may vary from state to

state or from province to province. This limited warranty does not cover any liability for consequential or incidental damages, all of which

are hereby expressly disclaimed, or the extension beyond the duration of this limited warranty of any implied limited warranties, including

those of merchantability or fitness for an intended purpose. In some states or provinces the exclusion or limitation of incidental or consequential

damages is not allowed, so those exclusions may not apply to you.

JADO Bathroom & Hardware Manufacturing Corp. provides the following warranties only to the first  residential owner of our products.

FINISHES  

JADO FAUCET LIFETIME FUNCTION AND FINISH LIMITED WARRANTY

3

5

6

ON

OFF

ON

OFF

AERATOR

SPOUT END

INSTALL CROSS HANDLES

Place ESCUTCHEON O-RING (1) in groove on back side of

ESCUTCHEON (2).

Install ESCUTCHEON (2) onto HANDLE ADAPTER (3).Thread

HANDLE ADAPTER (3) onto HANDLE SUPPORT (4) until tight

against finished wall. 

 

Turn valves to off position. Align CROSS HANDLE (5)

as shown or as desired. Install CROSS HANDLE (5) onto

HANDLE ADAPTER (3). Thread HANDLE BASE (6) until

tight against ESCUTCHEON (2).

4

Wall Mount

Vessel Faucet

832/34O/...

 Trim Only

832/375/...

1

INSTALL WALL BRACKET

Secure WALL BRACKET (1) to cross brace of wall structure

at required height using six wood screws.

NOTE TO INSTALLER:

 IF REQUIRED A DEEP ROUGH KIT IS 

AVAILABLE, PART NUMBER H960740.191.

WOOD SCREWS

CROSS BRACE

WALL STUDS

16"

2

INSTALL VALVE BODY

Mount VALVE BODY (1) to WALL BRACKET (2) as shown. Level and tighten 

SET SCREWS (3) to secure VALVE BODY (1) to WALL BRACKET (2).

Connect HOT water supply to LEFT INLET UNION (4) and COLD water supply

to RIGHT INLET UNION (5). Pipe connections are 1/2" NPT. Use sealant or

Teflon tape on pipe connections. 

Do not solder directly to valve body.

With valves closed open supply lines and check for leaks. Remove PLASTER

GUARDS (6) and open both valves and check for leaks.

HOT

COLD

Close both valves and turn off water supplies. Replace PLASTER GUARDS (6)

and finish wall construction.

-

Figure 2

1"

(25mm)

3/8"

HEX

GREASE O-RING

(SUPPLIED)

FINISHED

WALL

FACE

1-5/8" MIN.

(41mm)

1/2" NPT 

UNION INLETS

8"

(203mm)

5-1/4"

(133mm)

1"

(25mm)

7/8" MAX.

(22mm)

2-1/2" MAX.

(63mm)

FINISHED

WALL

FINISHED

WALL

2-3/8" D.

(60mm)

7-1/4"

(184mm)

IQ

                        

ON

OFF

OFF

Отзывы: