Jadever JWI-3100 Скачать руководство пользователя страница 5

Страница: 5 / 17

JWI-3000 4

CONN

E+
E-
S+
S-

LOAD-CELL

Shield

☆

Zeros the display

☆

Short press to save and exit from the setting mode

☆

Long press to exit from the setting mode without saving.

UNIT/SET

key

☆

Exchange the weighing units

☆

Long press to enter the parameter setting

3-3 Rear Panel

1. Port for connecting load cell

2. USB Port

3. RS-232 Port

4. Power socket

5. Power ON/OFF switch

3-4 Power supply

1. Switching power supply (100V~240V)

2. (6V/4A) Internal Rechargeable Battery

Power Consumption

330mW with backlight (about 70 hours available)

Low battery warming

When “

” appears in the upper left corner of the weight window, the battery power requires

recharging. The charge lamp turns green from red when the recharging is completed (which

takes about 8 hours). Disconnect the scale from power supply when it is fully charged.

4. Installation Instructions

4-1 Load cell connecting

CAN DIEN TU TAN HIEP THANH

www.tanhiepthanh.com.vn

Содержание JWI-3100


















Результаты поиска

Содержание JWI-3100

Отзывы:

Похожие инструкции для JWI-3100

Бренды по названию

Популярные бренды

Jadever JWI-3100, Руководство пользователя

Результаты поиска

Содержание JWI-3100

Отзывы:

Похожие инструкции для JWI-3100

Бренды по названию

Популярные бренды