Jadever JWI-3100 Скачать руководство пользователя страница 15

Страница: 15 / 17

JWI-3000 14

7-5 Input commands (Optional)

Connect the indicator and computer. Set Parameter P09 to “

” and P11 to “

Key

”. Run serial

port debugging program on the computer. Input the capital number “Z”, “T”, “R” in the sending

area, and the indicator can conduct the corresponding actions and have key sound at the same

time.

Z=zero T=tare R=print

8. Error message and trouble shootings

Error
Message

Problem

Solution

ERR0

Exceed the zero range

The item on the pan should be within 2% of
full load.

ERR1

Model setting error. Resolution
should be within 300-300000

Adjust or reset the capacity first then adjust
resolution

ERR2

Initial zero point exceeds 30% of full
load

1.Remove the obstacle article under the pan
2.Replace the load cell or contact the
maintenance department.

ERR3

Exceed the A/D resolution range

1. Replace A/D
2..Replace the load cell or contact the
maintenance department.

ERR4

EEPROM failure

Re-weld

EEPROM

contact

the

maintenance department.

ERR5

Overload condition

Remove the overload item

ERR6

Exceeds the display range

-----------------------------------------------

ERR8

Lower limit is higher than upper limit Reset the weight limit value.

ERR9

Exceed tare or pre-tare range

＜

Tare value

≤

full load

ERR10

Wrong calibration weights

Place the right test weights and the
calibration value should be below full load.

CAN DIEN TU TAN HIEP THANH

www.tanhiepthanh.com.vn

Содержание JWI-3100


















Результаты поиска

Содержание JWI-3100

Отзывы:

Похожие инструкции для JWI-3100

Бренды по названию

Популярные бренды

Jadever JWI-3100, Руководство пользователя

Результаты поиска

Содержание JWI-3100

Отзывы:

Похожие инструкции для JWI-3100

Бренды по названию

Популярные бренды