background image

ENGLISH

PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT.

The Company has obtained applicable code (standards) listings generally available on a national basis for products of this type.
It is the responsibility of the installer/owner to determine specific local code compliance prior to installation of the product.  The
Company makes no representation or warranty regarding, and will not be responsible for any code compliance.

NOTE:  This is a professional grade product.  A knowledge of construction techniques, plumbing and electri-
cal installation according to codes are required for proper installation and user satisfaction.  We recommend
that a licensed contractor perform the installation of all Jacuzzi Whirlpool Bath products.  Our warranty does
not cover improper installation related problems.

PRECAUTIONS

•••••

Do not operate the hydromassage system unless the bath is filled with water to at least 1" to 2" (2,5 - 5,08 cm) above the
highest jet.

•••••

Do not immerse the control panel by overfilling the bath.

•••••

Do not use oil-based bath additives in your hydromassage bath.

•••••

When cleaning your bath, do not use abrasive substances which will damage the bath's surface.

•••••

To prevent discoloration of the acrylic finish, do not fill the bath with water in excess of 140°F (60°C).

WARNING — WHEN USING THIS UNIT, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED,
INCLUDING THE FOLLOWING:
DANGER — 

RISK OF ELECTRIC SHOCK. CONNECT ONLY TO A CIRCUIT PROTECTED BY A GROUND

FAULT CIRCUIT INTERRUPTER (GFCI).

CAUTION — 

TEST THE GROUND FAULT CIRCUIT INTERRUPTER PROTECTING THIS APPLIANCE

PERIODICALLY IN ACCORDANCE WITH MANUFACTURER’S INSTRUCTIONS.

WARNING — 

USE THIS UNIT ONLY FOR ITS INTENDED USE AS DESCRIBED IN THIS MANUAL.  DO NOT

USE ATTACHMENTS NOT RECOMMENDED BY THE MANUFACTURERS.

WARNING — 

TO AVOID INJURY, EXERCISE CAUTION WHEN ENTERING OR EXITING THE HYDROMASSAGE BATHTUB.

WARNING — 

KEEP BODY AND HAIR A MINIMUM OF 6" (15,2 cm) AWAY FROM SUCTION FITTING AT ALL

TIMES WHEN THE HYDROMASSAGE SYSTEM IS OPERATING.  HAIR LONGER THAN SHOULDER
LENGTH SHOULD BE SECURED CLOSE TO THE HEAD.

WARNING — 

RISK OF ELECTRICAL SHOCK; DO NOT PERMIT ELECTRICAL APPLIANCES (SUCH AS HAIR

DRYER, LAMP, TELEPHONE, RADIO OR TELEVISION) WITHIN 60" (1,5 M) OF THIS HYDROMASSAGE BATHTUB.

WARNING — 

RISK OF ACCIDENTAL INJURY OR DROWNING; DO NOT USE DRUGS OR ALCOHOL

BEFORE OR DURING THE USE OF HYDROMASSAGE BATHTUB EQUIPPED WITH A HEATER TO AVOID
UNCONSCIOUSNESS AND POSSIBLE DROWNING.

WARNING — 

RISK OF FETAL INJURY; PREGNANT OR POSSIBLY PREGNANT WOMEN SHOULD

CONSULT A PHYSICIAN BEFORE USING A HYDROMASSAGE BATHTUB EQUIPPED WITH A HEATER.

WARNING — 

RISK OF HYPERTHERMIA AND POSSIBLE DROWNING; DO NOT USE A HYDROMASSAGE

BATHTUB EQUIPPED WITH A HEATER IMMEDIATELY FOLLOWING STRENUOUS EXERCISE.

WARNING — 

RISK OF HYPERTHERMIA AND POSSIBLE DROWNING; WATER TEMPERATURE IN

EXCESS OF 104°F (40°C) MAY BE INJURIOUS TO YOUR HEALTH.  CHECK AND ADJUST WATER
TEMPERATURE BEFORE USE.

WARNING — 

RISK OF HYPERTHERMIA; PEOPLE USING MEDICATIONS AND/OR HAVING AN ADVERSE

MEDICAL HISTORY SHOULD CONSULT A PHYSICIAN BEFORE USING A HYDROMASSAGE BATHTUB
EQUIPPED WITH A HEATER.

FOR BUILT-IN AND DROP-IN UNITS, INSTALL TO PERMIT ACCESS FOR SERVICING.

THIS UNIT SHOULD BE ELECTRICALLY GROUNDED AND INSTALLED BY A LICENSED CONTRAC-

TOR, ELECTRICIAN, AND PLUMBER.

BUILDING MATERIALS AND WIRING SHOULD BE ROUTED AWAY FROM THE MOTOR/PUMP OR

BLOWER OR OTHER HEAT PRODUCING COMPONENTS OF THIS UNIT.

A PRESSURE WIRE CONNECTOR IS PROVIDED ON THE EXTERIOR OF THE MOTOR/PUMP AND

HEATER TO PERMIT CONNECTION OF AN NO. 8 AWG (8.4 MM) SOLID COPPER BONDING CONDUCTOR
BETWEEN THIS UNIT AND ALL OTHER ELECTRIC EQUIPMENT AND EXPOSED METAL IN THE VICINITY,
AS NEEDED TO COMPLY WITH LOCAL REQUIREMENTS.

INSTALLATION  INSTRUCTIONS

3

Jacuzzi Whirlpool Bath   K339000X   3/06

Содержание CIPREA































Отзывы: