Jacobsen R311T-T4F Скачать руководство пользователя | Manualshive

Страница: 62 / 84

background image

9 MAINTENANCE

61

9.20 ELECTRICAL SYSTEM

____________________________________________________________

General precautions to decrease electrical problems are -

•

Make sure that all the connections are clean and correctly fastened.

•

Check the interlock system, fuses and circuit breakers at normal intervals. If the interlock system does not
operate correctly and you can not correct the problem, contact an authorized Jacobsen Dealer.

•

Keep the wiring harness away from hot surfaces and moving parts.

•

Make sure the seat switch wiring harness is connected to the mower wiring harness.

•

Check the battery and the alternator.

•

Do not wash or pressure spray around electrical connections and components.

9.20.1 CONTROLLERS __________________________________________________________

The mower’s electrical system is monitored and controlled by the controller found beneath the operator seat. The
controller has 2 light emitting diodes (LED) that can help to correct electrical system problems.

The mower engine is monitored and controlled by the engine controller found on the right side of the cowling. Two CAN
bus connectors are found near the engine controller. The four pin connector is for the Kubota Engine Controller (ECU
diagnostic connector. The three pin connector is for the mower’s controller (VCU) diagnostic connector.

CAUTION

Always turn the ignition switch to the off position and remove the negative (BLACK) battery cable before you inspect
or service the electrical system.

NOTICE

For factory help with the Mower Controller problems, give the hardware revision and software version found on the
mower’s controller. The replacement controllers with higher revision levels will be compatible.

For factory help or replacement of the Kubota Engine Controller, give the engine model and serial number found on
a plate on the engine valve cover.

!

F

A

UL

T

PO

WER

JACOBSEN

4275250

MTI500818

REV B

DATE YYWW

SOFTWARE

9572$-B

RoHS

Compliant

J1

J2

Software
Version

Hardware
Revision

Mower Controller

Engine Controller

Engine CAN Connector

Mower CAN Connector

«
...
60
61
62
63
64
...
»

Содержание R311T-T4F





















































































Отзывы:

Нет отзывов

Похожие инструкции для R311T-T4F

Бренд: LAZER Страницы: 20

532 42 27-27 Rev. 2

Бренд: McCulloch Страницы: 28

Бренд: SANLI Страницы: 16

Бренд: Garland Страницы: 172

Бренд: Etesia Страницы: 42

Zero Turn Radius Mower

Бренд: Country Clipper Страницы: 25

Бренд: Snapper Страницы: 8

Бренд: Alamo Industrial Страницы: 186

Бренд: Hitachi Страницы: 25

Бренд: Hitachi Страницы: 100

Бренд: Hitachi Страницы: 160

Бренд: Husqvarna Страницы: 44

Бренд: Husqvarna Страницы: 120

Бренд: Gardol Страницы: 324

STANDER X 79490219

Бренд: WRIGHT Страницы: 24

Бренд: Einhell Royal Страницы: 84

Бренд: Craftsman Страницы: 24

Бренд: Craftsman Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды