Jacobsen R311T-T4F Скачать руководство пользователя | Manualshive

Страница: 3 / 84

background image

INTRODUCTION 2

2

2Introduction

2.1

IMPORTANT ______________________________________________________________

The Jacobsen R311T with a Diesel engine is a self propelled rotary mower. The hydraulic systems are for the traction
drive, steering, lift - lower and the cutting unit drive.

If you follow all instructions in this manual, you increase the life of your mower and keep its maximum performance.
Adjustments and maintenance must always be done by an approved technician.

IMPORTANT: Do the maintenance included in this manual to make sure that the quality of cut is kept at a high level.

This SAFETY, OPERATION AND MAINTENANCE MANUAL is part of the mower and must stay with the mower
always. Suppliers of both original and used mowers need to keep the documentation that comes with the mower.

You must use the mower to cut the grass and not for any other purpose. Compliance with the conditions or operation,
service and repair specified by the manufacturer, are understood to be part of the correct use.

ALL operators MUST read through this manual and understand the Safety Instructions, controls, lubrication and
maintenance procedures.

Make sure that you obey all safety and road traffic regulations.

You must not make any changes to the mower that the manufacturer does not approve. This type of change can
release the manufacturer from the liability for any damage or injury.

When you discard worn parts, know the environmental result and use the systems available in the country where the
mower is used. When the mower is at its end of life, there are guidelines in this manual for the removal of the mower
from use.

Use only Jacobsen approved parts.

2006/42/EC

The instructions recorded here are the original instructions confirmed by Jacobsen, A Textron Company.

«
1
2
3
4
5
...
»

Содержание R311T-T4F





















































































Отзывы:

Нет отзывов

Похожие инструкции для R311T-T4F

Бренд: ECLOZ Страницы: 56

Бренд: Gardena Страницы: 70

Бренд: Gardena Страницы: 84

Бренд: Gardena Страницы: 24

Бренд: Gardena Страницы: 8

Бренд: Gardena Страницы: 60

Бренд: DR Страницы: 44

Бренд: Yard-Man Страницы: 8

Бренд: Scag Power Equipment Страницы: 20

Mowers DIESEL 1500cc

Бренд: Bad Boy Страницы: 54

Enviromower ENV369B

Бренд: Victa Страницы: 28

Бренд: Bad Boy Страницы: 36

Бренд: Kubota Страницы: 142

Бренд: Husqvarna Страницы: 47

Бренд: Husqvarna Страницы: 64

Бренд: Husqvarna Страницы: 56

Бренд: Husqvarna Страницы: 44

Бренд: Husqvarna Страницы: 59

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды