Jacobsen JMP653F Скачать руководство пользователя

Страница: 76 / 138

en-74

7 ADJUSTMENTS

7.7

GENERAL INSTRUCTIONS FOR GRAMMER SEATS________________________

To identify seat type, slide seat forward on its runners to reveal seat label.

All The seat adjustments are to be done while the vehicle is stopped.

• After removal of the backrest cover, hold the backrest frame in position with a support before the backrest

adjuster is operated. If you do not lock the frame in position safely, the backrest frame can move forward

suddenly and can cause injury.

• Use approved GRAMMER parts.

• Only GRAMMAR approved changes are to be made to the seat. During the removal and installation of the

GRAMMER driver seat, follow the instructions supplied by the vehicle manufacturer.

• When you lift the driver seat, do not hold the covers. The covers are not a load bearing component and injury

can occur.

• Before you remove the driver seat, disconnect all plug-in connectors between the seat and the vehicle supply

network. When you replace the plug-in connectors, make sure the connectors are tight so that dust and water

does not enter.

• Fasten seat belts before operation.

• Replace the seat belt after an accident.

• After an accident with a vehicle that has seat belts installed, have the seat and seat mounting checked by

the safety

personnel.

• Check the seat fasteners to make sure that the seat is installed correctly.

• If the seat does not operate correctly, have the seat repaired in a GRAMMER workshop. Check the seat for

damage to the seat suspension and bellows or for an incorrect curve in the lumbar support.

• If you do not correct problems that occur in the seat, the seat can damage your health and increase the risk

of an accident.

• Before the vehicle is used, check the load sensor, installed in the seat, for correct operation. If the driver

leaves the seat, this sensor stops the vehicle.

• If a problem is found, you must not drive the vehicle. – INCREASED RISK OF ACCIDENT –

• Do not put the loads on to seats that have a load sensor. A load on the seat can cause the vehicle to move

and cause an accident. – INCREASED RISK OF ACCIDENT –

• If you drive the vehicle and remove the weight from the seat, the vehicle will stop.

• Do not load the bellows while there is a load on the driver seat. – RISK OF INJURY FROM BELLOWS –

• Make sure that dirt and liquids can not get inside the drivers seat.

• The driver seat is not waterproof.

• Any changes or adjustment to a GRAMMER driver seat must be done in authorised workshops by approved

personnel. The changes must follow the operation instructions and must be in compliance with all national

regulations.

• Incorrect installation and assembly hold the risk of personal injury or property damage. Your warranty will also

be invalidated.

Содержание JMP653F











































































































































Результаты поиска

Содержание JMP653F

Отзывы:

Похожие инструкции для JMP653F

Бренды по названию

Популярные бренды

Jacobsen JMP653F, Руководство пользователя

Результаты поиска

Содержание JMP653F

Отзывы:

Похожие инструкции для JMP653F

Бренды по названию

Популярные бренды