background image

CONTROLS    2

6

2.2

CONTROLS _______________________________________________________________

A.

Tilt Steering 

Pull lever up to release steering column. Tilt column
up or down to position desired. Release lever to lock
steering column in place.

B.

Turn Assist

Reduces the turning radius of the machine for
operation in close areas. Use the turn assist pedals
for making tight turns around trees and other objects.
To operate turn assist, press pedal down gradually
until desired turning radius is achieved - left pedal
(

B1)

 for left turns, right pedal 

(B2)

 for right turns. 

Note:

 

Pressing pedal too hard will cause wheel to

lock up and may tear or mark the turf.

C.

Speed Limiter

Limits forward speed while cutting or operating
attachments. To operate at lower travel speed rotate
lever as shown 

(C

1

)

 so it contacts stop screw on floor

board when traction pedal is pressed forward. To
travel at full speed, set lever in position shown 

(C

3

)

.

Stop screw 

(C

2

)

 can be adjusted to set specific travel

speeds. 

Figure 2B

D.

Traction Pedal 

Press front pedal 

(D

1

down for forward travel.

Release pedal to slow mower and stop.

Press rear pedal (

D

2

) down for reverse travel.

Release pedal to slow mower and stop. Allow mower
to come to a complete stop before reversing
directions.

E.

Alarm

The alarm, along with the warning lights, sounds to
alert the operator to conditions requiring immediate
attention. See 

Section 2.4

.

F.

Hydraulic Oil Cap/Dipstick

Fill to green mark on dipstick using clean hydraulic
fluid while machine is cool. Do not overfill.

G.

Fuel Cap

Fill fuel tank with No. 2 diesel fuel, minimum cetane
rating of 45. See engine manual for additional fuel
specifications.

H.

Parking Brake

To engage parking brake pull up on lever. Always
engage parking brake before starting and after
stopping machine.

I.

Seat Adjustments

The standard operator’s seat has five adjustment
settings.

Description

Location on Seat

Raise/Lower Control 

left, front - under seat

Back Rest Tilt 

left, front - under seat.

Fore/Aft Control Bar 

front of seat

Back Lumbar Support  left side on back rest
Arm Rest Control 

under each arm rest

J.

Side Deck Transport Locks

Locks decks in upright position for transporting
mower. Locks must be manually released before
lowering decks. See 

Safety & Operation Manual

.

 

CAUTION

 Never adjust steering while mower is moving. Stop 

unit and set parking brake before adjusting.

!

Full Speed

Reduced Speed

C

1

C

2

C

3

HR023

Содержание HR 9016 Turbo



























Отзывы: