background image

SPECIFICATIONS    3

13

3.8

VIBRATION LEVEL_________________________________________________________

The mower was tested for hand and arm vibration levels. The operator was in the normal position to drive the vehicle,
with two hands on the steering mechanism. The engine was in operation and the cutting device was in rotation, while
the mower was not moving.

The Machinery Safety Directive 2006/42/EC
By compliance to:
The Lawnmower Standard BS EN ISO 5395-3
Referenced to Hand/Arm: BS EN ISO20643:2008

Information Supplied for Physical Agents Directive 2002/44/EC
By reference to:
Hand/Arm Standards: BS EN ISO 5349-1 (2001)
BS EN ISO 5349-2 (2001)

The mower was tested for Whole Body vibration levels. The operator was in the normal position to drive the vehicle,
with two hands on the steering mechanism.  The cutting device was in rotation with the mower driven in a straight line
at 6 Km/hr on a level and cut lawn.

The Machinery Safety Directive 2006/42/EC
By compliance to:
Whole Body EN1032:2003

Information Supplied for Physical Agents Directive 2002/44/EC
By reference to:
Whole Body Standards BS EN ISO 2631-1 (1997)

Greens King IV Plus

Hand/Arm

Acceleration Level

 62304, 62379

Maximum Left Hand or Right Hand Accelerations m/s

2

Mean Value of X, Y, Z Aeq

62304, 62379

1.10 ± 0.6

Greens King IV Plus

Whole Body

Acceleration Level

 62304, 62379

Maximum Seat Pad Accelerations m/s

2

Mean Value of X, Y, Z Aeq

62304, 62379

0.343 ± 0.056

Содержание Greens King IV Plus





























































Отзывы: