Jacobsen AR-522 jossa ROPS Скачать руководство пользователя страница 19

OPERATION    5

19

5.9

TOWING / TRAILERING _____________________________________________________

If the mower experiences problems and must be shut down 
and removed from the area, it should be loaded onto a trailer 
for transport. If a trailer is not available, the unit can be 
towed slowly for short distances. 

Use care when loading and unloading mower. Fasten mower 
to trailer to prevent mower from rolling or shifting during 
transport.

Long Distance Trailering / Transport. 

If the mower is to 

be trailered on the highway, before strapping to trailer, 
close fuel shut off valve and inflate tires to maximum 
pressure listed on side of tire. Reduce tire pressure to 
normal after removing from trailer. 

[See 5.10]

.

Before towing, open tow valve. The tow valve permits 
moving the mower without starting the engine and prevents 
possible damage to hydraulic components.

The tow valve 

(A)

, is located on the hydraulic drive pump 

beneath the operators seat. Remove cover from floor in front 
of operator’s seat. To open valve, use a wrench or insert a 
pin or small screw driver into the small hole in the valve 
stem. Turn the valve counterclockwise one full turn.

Before towing make sure cutting units are raised. If they 
cannot be raised, remove them from the mower.

Close valve completely and replace cover after towing.

Figure 5B

5.10 HILLSIDE OPERATION _____________________________________________________

The mower has been designed for good traction and stability 
under normal mowing conditions. Use caution when 
operating on slopes, especially when the grass is wet. Wet 
grass reduces traction and steering control.

1.

Always mow with the engine at full throttle, but reduce 
forward speed to maintain the proper cutting frequency.

2.

Activate traction control 

(S)

 as required to improve 

weight distribution between decks and mower. 

[See 

4.3]

.

3.

If the mower tends to slide or the tires begin to mark 
the turf, angle mower into a less steep grade until 
traction is regained or tire marking stops.

4.

If mower continues to slide or mark the turf, the grade 
is too steep for safe operation. Do not make another 
attempt to climb, and back down slowly.

5.

When descending a steep slope, always lower 
implements to the ground to reduce the risk of mower 
overturning.

Correct tire pressure is essential for maximum traction.

Front ......................... 16 psi (111 kPa)
Rear .......................... 12 psi (86 kPa)

NOTICE

Do not exceed 2 MPH (3.2 KPH) while towing. Long 
distance towing is not recommended

.

A

LF006

 

WARNING

To minimize the possibility of overturning, the safest 
method for operating on hills and terraces is to travel up 
and down the face of the slope (vertically), not across the 
face (horizontally). Avoid unnecessary turns, travel at 
reduced speeds, and stay alert for hidden hazards.

 

CAUTION

Do not operate this mower on slopes greater than 20°.

!

!

Содержание AR-522 jossa ROPS

























































Отзывы: