background image

 

Revision 08/29/12  B 

 

LC_XO Low Cost Ultra Small 1x1 inch GPSDO Module Spec 

 

0.97 X 0.97 X 0.5 inch Module with 

pins 

 

< 1 Min. Crystal Warm Up 

 

50 Channel WAAS GPS Receiver 

 

Very Low Power, TCXO or OCXO 

PRELIMINARY SPECIFICATION

TYP. ELECTRICAL SPECIFICATIONS: 

Module Specification: 

 

1 PPS Accuracy 

±50ns to UTC RMS (1-Sigma) GPS Locked 

Holdover Stability  

<±20us over 3 Hour Period @+25

°

C (No Motion, OCXO) 

1 PPS Output 

3.3VDC CMOS 

Serial Control 

SCPI-99 TTL Level, GPS NMEA Output 

GPS Frequency 

L1, C/A 1574MHz 

GPS Antenna 

Active or Passive 

GPS Receiver 

50 Channels, Mobile, SBAS WAAS, EGNOS, MSAS capable 

Sensitivity 

Acquisition –142 dBm, Tracking -158 dBm 

GPS TTFF 

Cold Start -  <45 sec, Warm Start – 1 sec, Hot Start - 1 sec 

ADEV 

10Ks <5E-012 (OCXO, GPS Locked, 25

°

C, no motion) 

TTL Alarm Output 

GPS LOCK indicator 

Warm Up Time / Stabilization Time 

<5 min at +25°C to 1E-08 Accuracy 

Supply Voltage (Vdd) 

3.3V Single-Supply only (5V internally generated and filtered) 

Power Consumption 

0.7W with OCXO, 0.5W with TCXO 

Operating Temperature 

0°C to +60°C, -20C to +75C optional 

Storage Temperature 

-45°C to +85°C 

Additional Features 

Firmware field-upgradable, external 1PPS input, status LEDs, compatible 

to GPSCon, SNTP, GPSD, and Z38xx software applications, full NMEA 

Oscillator Specification (OCXO): 

 

Frequency Output 

10MHz CMOS 5Vpp (3.3Vpp optional) 

10MHz Retrace 

±2E-08 After 1 Hour @ +25°C 

Frequency Stability Over Temperature (Unlock Condition) 

±2.5E-08 (OCXO) ±7.5E-08 (TCXO) 

Output Amplitude 

5Vpp CMOS 

OCXO Warm Up Time 

< 1 min @ +25°C 

Phase Noise (with 33uF or larger cap on 5V_Output pin 6) 

 TCXO OCXO 

1Hz -65dBc/Hz -75dBc/Hz 

10Hz -102dBc/Hz -110dBc/Hz 

100Hz -132dBc/Hz  -132dBc/Hz 

1kHz -148dBc/Hz -142dBc/Hz 

10kHz -152dBc/Hz  -145dBc/Hz 

100KHz <-155dBc/Hz  <-150dBc/Hz 

 

 

Connections: 

Connector Type: 

1PPS Output, 10MHz Output, power, serial communication, system 
status, NMEA, 1PPS in, ISP mode enable, antenna input 

100 mil spacing on pins, can be soldered, or plugged into a socket, gold-

plated pins 

 

   

  

 

Jackson Labs Technologies, Inc., 475 Alberto Way, Suite 120, Los Gatos, CA 95032 

Phone: (408) 354-7888, Fax: (408) 354-7880,   

www.jackson-labs.com

 

[email protected]

 

 

Содержание LC_XO



















































Отзывы: