background image

FireFly-1A User Manual

14

© 2011 Jackson Labs Technologies, Inc.

 

3.5.10 SYNChronization?

This query returns the results of these six queries :

SYNChronization:SOURce:MODE?

SYNChronization:SOURce:STATE?

SYNChronization:LOCKed?

SYNChronization:HOLDover:DURation? 

SYNChronization:FEEstimate?

SYNChronization:TINTerval?

SYNChronization:health?

3.6 DIAGnostic Subsystem

This subsystem regroups the queries related to the diagnostic of the OCXO.The list of the commands 
supported for this subsystem is as follows:

DIAGnostic:ROSCillator:EFControl:RELative?

DIAGnostic:ROSCillator:EFControl:ABSolute?

3.6.1 DIAGnostic:ROSCillator:EFControl:RELative? 

This query returns the Electronic Frequency Control (EFC) output value of the internal reference 
oscillator. It returns a percentage value between -100% to +100%. :

3.6.2 DIAGnostic:ROSCillator:EFControl:ABSolute? 

This query returns the Electronic Frequency Control (EFC) output value of the internal reference 
oscillator. It returns a value in volts between 0 and 5 V

3.7 MEASURE Subsystem

This subsystem regroups the queries related of some parameters that are measured on-board on the 
FireFly-1A. The list of the commands supported for this subsystem is the following:

MEASure:VOLTage?

MEASure:CURRent?

MEASure?

3.7.1 MEASure:VOLTage?

This command is not supported in FireFly-1A, and will return undetermined values.

Содержание FireFly-1A GPSDO













































Отзывы: