background image

 

 

 

 
 
 

Unpacking

 

Ice Maker Installation

 

 

 

  

Excessive Weight Hazard

 

Use two or more people to move and install ice maker. 

Failure to do so can result in back or other injury. 

 

 

 

Remove packaging materials

 

 

IMPORTANT:  Do  not  remove  any  permanent  instruction  labels  or  the  data  label  on  your  ice 
maker.

 

Remove tape and glue from your ice maker before using. 

 

• 

To  remove  any  remaining  tape  or  glue,  rub  the  area  briskly  with  your  thumb.  Tape  or  glue 

residue  can  also  be  easily  removed  by  rubbing  a  small  amount  of  liquid  dish  soap  over  the 
adhesive with your fingers. Wipe with warm water and dry. 

 

• 

Do  not  use  sharp  instruments,  rubbing  alcohol,  flammable  fluids,  or  abrasive  cleaners  to 

remove tape or glue. These products can damage the surface of your ice maker. 

 

Cleaning before use

 

 

After you remove all of the packaging materials, clean the inside of your ice maker before using 
it. See "Interior cleaning" in the 

Cleaning and Maintenance 

section. 

 

Location Requirements

 

 

Top View 

Side View 

 

 
 
 
 

2/5" 

1" 

 

Top of unit 

 
 

1/5" 

Side 

1/5" 

 

Side 

 

 
 

Front of unit 

 

 

 

INSTALLATION CLEARANCES

 

Содержание AZ-20A





























Отзывы: