The JA-62GSM communicator for GSM
The JA-62GSM communicator for GSM
2 / 11
MLD52902
Example
by sending: “SET code” (SET space valid code) the system will set
(if it is already set it will not change its status)
Notes:
−
the access code is always required for the commands SET and UNSET
−
the system will
confirm performance of the SMS
instruction by an
SMS reply, if this function is enabled
−
the SMS instruction texts are not case-sensitive and only ASCII
characters are allowed
−
the SMS instruction texts can contain multiple instructions separated with
a comma
−
if you are sending an instruction and you are not sure whether any other
text will be automatically added to the SMS on the way (for example,
when using an SMS internet gate) type the instruction as:
%instruction code %%
−
the valid code can also be entered automatically, see 6.6.
4. User communicator programming
User setting of the communicator is performed by entering sequences from
the Profi system keypad. Selected parameters can also be controlled or set
by SMS instructions.
Setting on the system keypad is possible only in the case that the control
panel is in
maintenance mode
(if it is not, enter F0 master code when
system is unset – Factory default setting 1234). Modification of values set in
the communicator is performed by entering programmable sequences (see
Press the # button to exit Maintenance mode
or to cancel code entering
when you enter a wrong number.
If setting of telephone numbers in Maintenance mode is enabled in the
control panel settings (sequence 251 of the Profi control panel), then it is
possible to set the following communicator parameters in Maintenance mode
by keying in the below mentioned sequences beginning with 8:
−
Set telephone numbers M1 to M8
−
Select events which should be reported by an SMS message and calling
−
Measure GSM signal strength
−
Limit the number of sent SMSes
−
Record voice messages
4.1. Setting of telephone numbers for reporting
The communicator reports events in the Profi system by sending a text
SMS and / or calling and transmitting a voice message. Reporting can be
programmed for to up to 8 telephone numbers.
The most frequently desired reports are already assigned to the telephone
number memories by factory-default, so you only need to program tel.
numbers to the particular memories:
Overview of reports assigned to tel. numbers (this can be modified see 6.4)
M
Reports
1
Alarms by SMS and phone call, faults by SMS
2
Alarms by SMS and phone call
3
Alarms by SMS and phone call
4
Alarms by SMS
5
Alarms by SMS and phone call
6
Alarms by SMS and phone call
7
Alarms by SMS
8
Technical faults by SMS (for a service technician)
tab. 2 Reports assigned to telephone number memories M1to M8
To program phone numbers to the M memories, enter the following
sequence while in Maintenance / Service mode:
81 M xxx...x F0
where:
M
is memory number 1 to 8
xxx...x
is a telephone number (max. 20 digits)
To erase a number from memory M enter:
81 M F0
Example:
entering
81 5 777 777 777 F0
will store the number 777777777 in
memory M5 (alarms will be reported by SMSes + phone calls with a voice
message).
Notes:
−
In a split system, when you change a detector’s section, adjust the
reaction of the detector etc, you have to enter enrollment mode for 1 s
and leave it before you leave service mode. This way the changes are
saved in the communicator.
−
Entering F9 before the first digit will insert a “+” for the international
formatting of phone numbers.
−
SMS report text consists of the installation name, event type, name of the
event source, date and time. For example: “Report from your alarm:
setting 47: device Time 11:27 01.08 ”.
−
If other events or texts should be reported to a particular number, change
the communicator settings (see 6.4, 6.7 and tab. 5 the list of events
which can be reported to your phone and their factory default settings).
5. Voice menu for control via a telephone
The communicator is equipped with voice navigation for remote control of
the basic system functions (remote access via a telephone must be enabled).
The menu has factory default voice reports in multiple languages – the
desired languages is selected by entering the
991 xx
sequence (see 6.1).
The voice navigation is as follows:
−
After 15 seconds of ringing the communicator will answer the call and
require entering the valid code.
−
After entering a valid code for remote access the system reports its
current status (always 1x) and opens the keypad simulation mode and
allows entering the controlling / programming sequences.
−
When you enter a valid access code, the system is set / unset and
confirms the system status. For an incorrect entry the system generates
a series of beeping sounds.
−
When you enter programming sequences, a correct entry is confirmed
by one beep, an incorrect entry is rejected and indicated by a series of
beeps.
−
When the system is in the service / maintenance mode, code verification
is performed and if the code is valid, you will hear: “Service mode,
keypad simulation“.
−
By entering the sequence 892, you enter the voice message recording
mode.
6. Installation programming
The most convenient and complete programming is best done by a PC
running Comlink software and higher connected locally at the installation or
remotely via the Internet.
The communicator can also be programmed by keying in sequences from
the system keypad or via SMS programming instructions.
Programming by the system keypad is possible only if the control panel is
in
Service mode,
if it is not, key in *0 Service code (factory default setting:
6060) with the alarm system unset (disarmed) The setting is performed by
keying in programming sequences, (see Tab. 7 communicator programming
sequences).
Press the # button to exit service mode
or to cancel code
entering when you key in a wrong number.
6.1. Communicator language setting
The language of the texts and voice menu used by the communicator can
be set by the instruction:
991 xx
where:
xx
is a number defining the language – see the following
list:
01
EN
English
08
IT
Italian
02
CZ
Czech
09
PT Portuguese
04
NL
Dutch
10
FI
Finnish
05
DE
German
12
SV Swedish
06
PL
Polish
14
HU Hungarian
07
DA
Danish
15
RU Russian
Example: Keying in 99101 will set English.
Notes:
−
entering 00 will reset the texts and voice messages to the factory default
values in the currently set language.
−
set the language before editing the text in the system (a change of
language will change the text to the factory default setting)
−
The set language will not change when a reset is performed
Factory default setting:
99101 = English
6.2. GSM signal strength measuring
A good quality GSM signal is necessary for the reliable functioning of the
communicator. Enter the
888
to start GSM signal strength measuring. The
keypad then displays the signal strength in the range 0 to 9 and the
measuring is repeated every second – new data is indicated by a beep. This