jablotron JA-60GSM, Руководство по установке, Страница: 8 / 12

JA-60GSM communicator module - 8 - MFJ51212
ƒ
If you are going to change the current SIM card in the dialer for
another one and the former one used a PIN code, enter
programming mode first and enter 70F0 (PIN code erasing in
the dialer).
5.2 GSM signal checking
If this function is enabled, the dialer will check regularly whether the
GSM signal is available. If it is not available for more than 15 minutes,
the system will indicate an external communication failure (failure L).
910
checking disabled
911
checking enabled
Default setting: checking disabled (910)
5.3 Reaction to an incoming call (remote access)
This sequence sets how the dialer will react to incoming calls. This
setting is important for remote access by telephone.
93 x
where
x = 0 no reaction to an incoming call
x = 1 to 8 will answer after 1=5sec., 2=10sec.,…,
8=40 seconds
x = 9 will answer after the second call = after the
1
st
ring is detected, there must be a pause
of 10 - 45 seconds. The dialer will answer
on the very first ring of the second call.
This setting can be used to bypass an
answering machine connected to the
phone output.
Default setting: 935 – the communicator will answer after 25 seconds
5.4 Remote access code setting
The following sequences are used for programming:
5.4.1 Service remote access code
94 xxxxxxxx F0
where
xxxxxxxx is the code, it can have 1 to 8 digits
If you enter 94F0 - the code will be erased and the remote access to
the alarm system will be not allowed .
Default setting: 0000 (4 zeros)
5.4.2 User remote access code
94 xxxxxxxx F1
where
xxxxxxxx is the code, it can have 1 to 8 digits
If you enter 94F1 - the code will be erased and user remote access to
the alarm system will be not allowed .
Default setting: 1111
5.5 Confirmation SMS reply messages
After the valid processing of an incoming SMS command, the dialer
automatically replies to the sender with a confirmation SMS message.
This confirmation is selectable:
950
automatic reply is disabled
951
automatic reply is enabled
Note: if the automatic reply is disabled, you can request a reply
manually by adding a space and the letter C after the last character of
the SMS instruction.
Default setting: 951 – automatic reply is enabled
5.6 Reset to default settings
Entering 96060 will cause the return to the default settings (all
telephone numbers will be erased, all unsent data will be erased and
the factory default SMS texts will be reloaded).
5.7 Total reset – all communications disabled
Entering 96061 will erase all of the settings in the dialer’s memory and
the list of SMSes will be set to default setting.
5.8 One-time dialing-in during programming mode
While the control panel is in the programming mode, you can enable
one-time remote access by entering 970 . After this code has been
entered, the dialer will respond to the first ring of any incoming call.
Without requesting the access code, it will enable the calling phone’s
keypad to be used as the keypad of the alarm system (
∗
= F, # = N).
This mode will be disabled after you dial-in, or after you exit
programming mode.
5.9 GSM signal monitoring
Enter 971 on the alarm system keypad (in programming mode) to
measure the GSM signal strength. The keypad will show a number
from 0 to 9 and it will sound a beep every second indicating a new
measurement each time. For proper functioning of the module the
signal strength should be 3 or higher. Find the best location for the
antenna while measuring the signal strength. To switch the system
back to programming mode press the N key.
Note: The standard antenna supplied with the JA-60GSM has a gain
of +3dB.
5.10 Attached phone function
The dialer provides a PHONE output to connect an ordinary
telephone set. The function of this telephone can be modified by
entering:
98 y
Where Function
y = 0 An ordinary telephone line is simulated, it is possible to
make phone calls (indicated with a dial tone in the
receiver)
1 If you pick up the receiver, the telephone keypad will work
as the keypad of the alarm system. It is impossible to
make phone calls in this mode (you will hear sounds of
the alarm keypad in the receiver)
y = 2 Disabled - the telephone has no function
y = 3 Emergency call – if you pick-up the phone, it will
automatically dial the emergency number (see 5.11)
Notes:
ƒ
If y=0 and you pick up the phone, the telephone keypad can be
switched to the alarm system keypad mode by pressing the #
key.
ƒ
If y=3 and you press the
∗
key less than 2 seconds after you pick
up the phone, you will hear the dial tone and you can then call
any number. If the # key is used the same way, the keypad will
switch to the alarm system keypad mode.
Default setting: y = 0 ordinary telephone line is simulated
5.11 Setting the emergency call number
If the attached telephone is programmed for emergency calls (see
section 5.10), it dials the emergency number after you pick up the
receiver. This number can be entered by:
99 xx...x F0
where:
xxx…x is a telephone number (max. 20 digits), enter
F9 before the number if you need + prefix
for international calls
Default setting: no phone number is set (99F0)
5.12 Function of attached SMS-8010 phone
The communicator has a telephone connector, which can be used for
connection to a SMS-8010 phone. A detail description is in the
separate manual enclosed with the SMS-8010 phone. To use an SMS
phone enter code 001 instead of the telephone number (see chapter
3.1)
Setting:
ƒ
For sending SMSs to mobile phones it is necessary to set SMS
center 1 to “1111”..
ƒ
By sending SMSs to telephone number “001”, the central
panel can be controlled using SMS instructions
Note:
ƒ
Displaying the caller’s telephone number (CLIP): The
telephone number is shown in the international format
(00420212345678).
ƒ
If the phone call is made from a JA-60GSM a telephone
number of 001 and name of the caller “
JA-60GSM“ will be
displayed.