jablotron JA-60GSM, Руководство по установке, Страница: 10 / 12

JA-60GSM communicator module - 10 - MFJ51212
7.4 Events to be reported to CMS
There are 31 types of events, which can be reported to each CMS –
see table 7.4.1. This sequence sets which events should be reported
to CMSs.
05 p uu y
where
p 1 = CMS1, 2 = CMS2
uu events index – see table 7.4.1
y 0 = report disabled, 1 = report enabled
Default setting: all reports are disabled
7.4.1 Table – complete list of events to be reported to CSM
Events index uu Events description
01 Intruder alarm – instant zone
02 Intruder alarm – delayed zone
03 Fire alarm
04 Panic alarm
05 Wrong access code alarm
06 Alarm after power on
07 Tamper alarm
08 Tamper OK
09 Alarm end
10 Alarm canceled by a user
11 Arming
12 Disarming
13 Partial arming (Home)
14 No code arming
15 External communication failure
16 External communication recovery
17 Failure
18 Failure recovery
19 AC failure longer than 30 minutes
20 AC failure
21 AC recovery
22 Battery failure
23 Battery recovery
24 Enter programming mode
25 Exit programming mode
26 Remote access
27 Remote access – end
28 RF jamming
29 Internal communication failure
30 Internal communication recovery
31 Periodic test
7.5 CMS re-dialing pause setting
If the dialer is activated it attempts to make a connection (alternating
between the primary and the backup telephone number). If it is not
possible to make a connection, a pause is initiated. After this pause
the dialer will attempt again. The pause length can be set in the
following way:
06 p t
where
t pause duration x 5 minutes (1 = 5 minutes, 2 = 10
min,..., 9 = 45 minutes)
p 1 = CMS1, 2 = CMS2
Default setting: 5 minutes for both CMSs
7.6 Interval of periodic test
The periodic test for checking the CMS link is set by activating event
No 31. The following sequence sets the time length from the last
reported event to the moment when the periodic test report should be
transferred.
07 p hhmm
where
p 1 = CMS1, 2 = CMS2
hh hours
mm minutes
Default setting: The periodic test report is sent 24 hours after the last
reported event.
7.7 Disabling CMS communication
If you need to disable all CMS reports temporarily, you can do this,
while retaining your settings:
0 0 p 0
all reports to CMS p disabled
0 0 p 1
all reports to CMS p enabled
Default setting: all CMS reports disabled.
7.8 CMS 2 as a back up for CMS1
CMS 2 can serve as an optional back-up for CMS if data transfer to
CMS1 fails. When the first event is transferred to the backup
monitoring station (CMS2) an event “tel. line #1 communication fault“
will be reported.
080 CMS1 and CMS2 are two independent stations
081 CMS 2 works as a back up for CMS 1.
When 081 is selected, CMS 2’s settings are used only in the case of
CMS 1 transfer failure.
Default setting : two independent CMSs.
7.9 Storing the event “data to CMS sent” into the event memory
By this sequence it is possible to disable recording of the event that
indicates that data to a CMS has been sent to the list of event in the
control panel.
Programming sequences:
090 The CMS data transfer event is not recorded
091 The CMS data transfer event is recorded
Default setting : The CMS data transfer event is recorded
8 The modem function
The GSM communicator can also be used as an external modem for
accessing the Internet (GPRS format). It is necessary to have GPRS
activated in the SIM card and to have a connection cable connected to the
COM port of the PC. Support for MS Windows operating systems can be
found on the enclosed CD. The modem can only be used when all CMS
reports, SMSs and system calls have been executed.
When the modem is used:
ƒ
It is possible to use the attached telephone, the internet connection will
be temporally suspended
ƒ
Received SMSs are stored and they will be processed after modem
disconnection
ƒ
The modem will be disconnected if an alarm or an arming event occurs
9 Additional information
9.1 Priorities for event reporting:
If the dialer is activated to send an event report it will:
ƒ
send information to CMS1 (trying primary and back up
numbers twice) if programmed
ƒ
send information to CMS2 (trying primary and back up
numbers) if programmed
ƒ
send SMS reports (1
st
telephone number, 2
nd
telephone
number,…. 8
th
tel. number)
ƒ
send audible reports (1
st
telephone number, 2
nd
telephone
number,…. 8
th
tel. number) – each number is only called
once, whether it is answered or not
ƒ
if the attempt to send a report to a CMS has not been
successful, the dialer will try to resend it after the re-dialing
pause (sequence 06px). The dialer will make three attempts
at sending event reports to a CMS, i.e. it will wait (according
to the setting 06px) twice for the re-dial pause. Only a new
event will result in an additional attempt to call the CMS.
If any event is triggered which should be reported to a CMS while the
alarm system is being remotely accessed by phone, the report will be
sent after remote access has finished.
If a user cancels an alarm, all reports, which have not been sent yet,
will be deleted, except for CMS reports.
9.2 The LED on the dialer PCB
•
LED flashing means the dialer has not entered the GSM network
•
LED flashing (3x) – the communicator (modem) is controlled by a PC.
•
LED being on means– communication with a GSM network
−
connecting to the GSM network
−
the dialer is calling
−
the dialer is sending an SMS
9.3 Entering programming mode
•
The dialer will finish the current CMS connection (the attached
phone will ring shortly to confirm this)
•
The current audible warning is interrupted immediately
•
SMSs and audible warnings, which remain unsent before entering
programming mode, are erased – they will not be sent after exiting
programming mode