Jabiru 2200 Скачать руководство пользователя

Страница: 149 / 201

Engine Overhaul Manual

Jabiru Aircraft

Pty Ltd

Jabiru 2200 & 3300 Aircraft Engines

This document is controlled while it remains on the Jabiru server. Once this no longer applies the document becomes uncontrolled.

ISSUE

6 7

Dated : 28/10/2014

Issued By: AS

Page: 149 of 201

L:\files\Manuals_For_Products\Engine_Manuals\Overhaul_Manual\JEM0001-7_Overhaul_Manual_DRAFT_(29_10_14).docx



During assembly, check each HT lead fitting for tightness in the distributor cap; expand each metal

fitting until it snaps neatly into place in the cap.



NGK D9EA spark plugs are used in Jabiru Engines. If other brands are used care must be taken to

ensure they are equivalent to the D9EA in all respects. Note that Resistor type plugs are not
recommended as they reduce the spark strength and can contribute to difficult starting

– and that

Iridium plugs are generally resistor types.



The spark plug gap is set to the value given in Table 12

. Generally around 0.23” works well though the

gap can be reduced to the minimum (0.018”–0.020”) during winter to give easier starting



Always use a high-temperature graphite lubricant such as anti-seize when fitting the plugs. Tighten the

plugs to the setting given in Table 9. Note that excess lubricant on the plug thread can cause plug
misfiring when heated.

Figure 192

– HT Leads Fitted To Engine

REMOVE ENGINE FROM STAND.

7.8.15 Front Crankshaft Seal Housing

Figure 193

– Fitting Seal To Housing

HT leads fitted. Note how
leads

are

bundled

and

restrained to prevent rubbing.

Содержание 2200










































































































































































































Результаты поиска

Содержание 2200

Отзывы:

Похожие инструкции для 2200

Бренды по названию

Популярные бренды

Jabiru 2200, Руководство по капитальному ремонту

Результаты поиска

Содержание 2200

Отзывы:

Похожие инструкции для 2200

Бренды по названию

Популярные бренды