J.P. Instruments EDM-700 Скачать руководство пользователя страница 35

Страница: 35 / 68

For Your Safe Flight

Page 31

Refer to the column in the chart below corresponding to your fuel tank
configuration. Tap the

button to select one of the four following

fueling choices on the left column of the chart.

LF to
choose

⇓

Main tanks

only, no tabs

Main tanks

with tabs

Main & Auxiliary

tanks

FILL?

DID NOT ADD ANY FUEL SINCE LAST SHUTDOWN.

FILL

Topped the
main tanks.

Filled only to the
tabs.

Topped the main
tanks. If some
additional fuel is
added to the auxiliary
tanks, you will input
this next when

GAL

is displayed

FILL

I20

(not available)

Topped the main
tanks.

Topped both the main
and auxiliary tanks.

FILL

DID NOT TOP, BUT ADDED ADDITIONAL FUEL TO THE
AIRCRAFT, OR REMOVED FUEL FROM THE AIRCRAFT.

Then tap the

STEP

button to complete the entry and advance to the

Manual mode.

Adding Fuel and Auxiliary Tanks

If you either

added less than full fuel to only the main tanks, or

topped the main tanks but have some fuel remaining in the
auxiliary tanks,

then select

FILL

+ and the next display will ask you how much you

added:

.0 GAL

(or selected units). Hold the

button to count up, tap

the

button to count down. The count up will stop at full tanks, since

you cannot add more fuel than would top the tanks.

If you added fuel to only the main tanks, then input how much you added.

If you topped the main tanks, but have some fuel remaining in the
auxiliary tanks, input how much is now in the auxiliary tanks.

You can “add” a negative amount of fuel if you remove fuel from the
aircraft or wish to correct the total quantity of fuel on board.

Содержание EDM-700





































































Результаты поиска

Содержание EDM-700

Отзывы:

Похожие инструкции для EDM-700

Бренды по названию

Популярные бренды

J.P. Instruments EDM-700, Руководство пилота

Результаты поиска

Содержание EDM-700

Отзывы:

Похожие инструкции для EDM-700

Бренды по названию

Популярные бренды