J.P. Instruments EDM-700 Скачать руководство пользователя страница 30

Страница: 30 / 68

Page 26

Engine Data Management

Display

Symptom

Probable Cause

Recommended

Action

EGT and CHT
not uniform

Dirty fuel injectors
or fouled plugs.

Check injectors and
plugs. Non-
uniformity is normal
for carbureted
engines

Decrease in
EGT for all
cylinders

Decrease in airflow
into the induction
system. Carb or
induction ice.

Engine units set to
Celsius

Check for change
in manifold
pressure.

Check that the
alarm limits are set
to Celsius degrees

Slow rise in
EGT. Low
CHT

Burned exhaust
valve. CHT is low
due to low power
output.

Have compression
checked.

High CHT on
cylinders on
one side of
engine

Obstruction under
cowling.

Check for improper
installed baffling,
cowl flap
misalignment or
bird nests.

EGT on one
cylinder jumps
up and down
100°

Spark plug fouling
at higher
temperatures.

Check spark plug.

Sudden off
scale rise for
any or all
cylinders

Pre-ignition

or Normalize view.

or failed probe

Full rich and reduce
power.

Change to
Percentage view.

Check probe

Содержание EDM-700





































































Результаты поиска

Содержание EDM-700

Отзывы:

Похожие инструкции для EDM-700

Бренды по названию

Популярные бренды

J.P. Instruments EDM-700, Руководство пилота

Результаты поиска

Содержание EDM-700

Отзывы:

Похожие инструкции для EDM-700

Бренды по названию

Популярные бренды