background image

10

QUATTRO LITE MANUAL

241 SUB MICRO SERVO PREPARATION

Using a Phillips screwdriver, remove the servo arm retaining screws from each of the 241 servos as shown
in Figure 1. Next, install 2 servo grommets and 2 servo eyelets to each 241 servo as shown in Figure 2.

SYSTEM CHECK

Slide the power ON/OFF switch on your Quattro
Transmitter to the “ON” position.

Next, slide the ON/OFF switch on your flight pack
switch to the ON position.

By moving each of the two transmitter sticks in a
fore-aft, left-right motion, the corresponding
throttle, rudder, elevator, and aileron (optional)
servo arm/wheel will rotate. Please refer to the
transmitter stick function chart below.

With the system still activated (ON), move the
throttle stick to the neutral (center) position.
Double-check to be sure that the four transmitter
trim levers are still in their neutral position.

Next, with the power still activated to the
transmitter and flight pack, remove the servo
arm/horn from each of the 241 servos. Then, 

turn the power OFF to the flight pack first, then the
transmitter. By doing this, the 241 servos will be left
in their neutral position, and they are now ready to
be installed into your model.

NOTE:

Save the servo arms/horns; they will be

reattached to the servos after installation.

8.3

8.4

Throttle/ESC

Throttle/ESC

Rudder

(optional)

Elevator

Elevator

Rudder or Aileron

Rudder or Aileron

Rudder

(optional)

Servo Case

Servo Lead w/Connector

Servo Mounting Flange

Servo Arm/Horn

Servo Arm Retaining Screw

Figure 2

Figure 1

Servo Arm Retaining Screw
(Phillips Head).

Servo Output Shaft

Rubber Grommet

Servo Eyelet

JRP4477.46 Update Quattro  1/29/01  4:20 PM  Page 10

Содержание Quattro Lite





















Отзывы: