background image

WARNING 

Do not allow toxic substances such as lubricants, solvents, or similar sub-

stances to flow into the local sewage system or river systems. Do not drain haz-

ardous liquids such as chemical solutions discharged out of the pump directly onto

the ground.  Instead, drain such liquids into some kind of container.  Observe the

laws and regulations related to the application, handling, and processing of haz-

ardous substances.

Do not pass under a raised pump.

Never pass under a raised pump.  A serious injury could occur if the pump is acciden-

tally dropped.

No remodeling!

Remodeling of the pump by the user may result in serious personal injury, electric

shock, or damage to the pump.  Do not attempt remodeling as it is very dangerous.

Cautions when dangerous liquids are transferred.

When the pumps are used to transfer the dangerous liquids mentioned as below, the

pumps always must be checked and watched so that the liquids can not be leaked.

The operation of the pumps leaking the liquids may result in personal injury and/or

explosion, fire accidents.

Explosive, fire-spreading and inflammable liquids

Corrosive and stimulus toxic liquids

Liquids detrimental to health

CAUTION 

Qualified operators only!

The pump operator and pump operation supervisor must not allow any operators who

have little or no knowledge of the pump to run operate the pump.  Pump operators

must have a sound knowledge of the pump and its operation.

For specified application only

The pump is designed and manufactured to the specifications agreed upon by the

user and IWAKI.  The use of a pump in any application other than those clearly speci-

fied may result in injury or damage to the pump.  Use the pump strictly in accordance

with the pump specifications and application range.  If you change any specification,

contact IWAKI or your dealer.

Ventilate!

Poisoning may result during an operation which involves toxic or odorous liquid.

Ventilate the operating site sufficiently.

- 3 -

Prohibited

No Remodeling

Safety Section

Prohibited

Caution

Содержание MDF-L series















































Отзывы: