IVT GBC-43 Скачать руководство пользователя страница 9

Страница: 9 / 104

Manual instruction |

Gasoline grass trimmer - Gasoline brushcutter

into the air.

WARNING: Use the shoulder harness at

all times adjust both harness and

harness clamp on the unit so that the

unit hangs a few inches above ground level .The

cutting head and the metal debris shield should

be level in all directions. Harness the unit on the

right side of your body.

WARNING: do not use a brush cutter for

cutting trees and never try to mount on

a saw blade on this machine

Fuel and oil mixture

Never fill the fuel tank to the very top.

Never add fuel to the tank in a closed non-

ventilated area.

Do not add fuel to this unit close to an open fire

or sparks.

Be sure to wipe off spilled fuel before attempting

to start the engine.

Do not attempt to refuel a hot engine.

Fuel used for this model is a mixture of unleaded

gasoline and approved engine lubricant. When

mixing gasoline with two-cycle engine oil, use

only gasoline which contains NO ETHANOL or

METHANOL(Types of Alcohol) Use Branded 89

octane or higher, unleaded gasoline known to be of

good quality. This will help to avoid possible damage

to engine fuel lines and other engine parts.

Mixture ratio

Fuel mixture at the rate other than 40:1 (2,5%) may

cause damage to the engine, Ensure that the

mixture ratio is correct.

Gasoline = 40 parts Oil = 1 part

Fuel

The engine uses two-stroke fuel, a mixture Two-

stroke fuel may separate. Shake fuel

of gasoline and 2-stroke lubricant 40:1 (2,5%)

container thoroughly before each use. Stored

fuel ages. Do not mix more fuel than you expect to

use within a month.

Gasoline

Use branded 89 octane or higher unleaded gasoline

known to be of good quality.

WARNING: do not mix fuel and oil

directly in the engine fuel tank!

Pre-operation check

When preparing the fuel mixture, mix only the

amount needed for the job. Do not use fuel that has

been stored longer than two months. Fuel mixture

stored longer than this will cause hard starting and

poor performance. If fuel mix has been stored longer

than this time. It should be removed and filled with

fresh mixture.

Never fill the fuel tank to the very top.

Never add fuel to the tank in a closed non-

ventilated area.

Do not add fuel to this unit close to an open fire

or sparks.

Be sure to wipe off spilled fuel before attempting

to start engine

Do not attempt to refuel a hot engine

Check this point before operating:

Check for loose bolts. Nuts and fittings.

Check the air cleaner for dirt. Clean the air filter

of all dirt. Etc. before operation.

Check to be sure that protector is securely in

place.

Check to be sure that there’s no leak.

Check to be sure the blade is not running in

idling speed.

WARNING: The engine exhaust from this

product contains chemicals known to

cause cancer, birth defects, or other

reproductive harm.

Operation

Starting a cold engine

Move the ignition switch (6) to “START” position.

Give a gentle push on the purge bulb (9)

repeatedly (7-10times) until fuel comes into the

primer pump.

Cold Starts: Pull lever up

to close choke (13).

Pull starter handle (14)

until engine fires.

Push choke lever (13)

inwards (excessive cranking

with choke lever will cause

flooding engine making it

Содержание GBC-43









































































































Результаты поиска

Содержание GBC-43

Отзывы:

Похожие инструкции для GBC-43

Бренды по названию

Популярные бренды

IVT GBC-43, Инструкция по эксплуатации и безопасности

Результаты поиска

Содержание GBC-43

Отзывы:

Похожие инструкции для GBC-43

Бренды по названию

Популярные бренды