8
Manual instruction |
Gasoline grass trimmer - Gasoline brushcutter
EN
in the debris being thrown
AWAY from you.
WARNING: Tilting
the head to the
wrong side will
shoot the debris TOWARDS
you. If the line head is held
flat to the ground so that cutting occurs on the
whole line circle, debris will be THROWN at you,
drag will slow the engine down, and you will use
up a lot of line.
Line head rotates in a CLOCK WISE direction. The
2.
cut-off knife (2) will be on
the right side of the debris
shield.
WARNING: Use
only
quality
n y
l
o
n
monofilament line of the diameter 2mm (GGT-25)
or 2.5mm (GBC-43) , Never use wire or wire-
reinforced line in place of nylon trimmer line. Load
your nylon line cutting head only with nylon
trimmer line of the proper diameter.
WARNING: Use extreme caution when
operating over bare spots and gravel,
because the line can throw small rock
particles at high speeds. Debris shields on the unit
cannot stop objects which bounce or ricochet off
hard surfaces.
TRIMMING
Tilt the head slowly to direct debris away from you.
If you are cutting near to a barrier such as fence, wall
or tree, approach from an angle where any debris
ricocheting off the barrier will fly away from you,
Move the line head slowly until the grass is cut right
up the barrier, but do not jam (overfeed) the line
into the barrier. If trimming up to a wire mesh or
chain linked fence be careful to feed only up to wire.
If you go to far the line will snap off around the wire.
Trimming can be done to cut through weed stems
one at a time. Place the trimmer line head near the
bottom of the weed-never high up which could
cause the weed to chatter and catch the line. Rather
than cut the weed right through, just use the very
end of the line to wear through the stem slowly.
SCALPING AND EDGING:
Both of these are done with the line head tilted at a
steep angle. Scalping is removing top growth
leaving the earth bear. Edging is trimming the grass
back where it has spread over a sidewalk or drive
way. During both edging and scalping, hold the unit
a steep angle and in a position where the debris, and
any dislodging dirt and stones, will not come back
towards you even if it ricochets off the hard surface.
every operator must find for himself the angles
which suits his body size and cutting situation.
(GBC-43)
The proper debris shield must be in place on the unit
when the nylon cutting line is used, The cutting line
can flap around if too much line is exposed. Always
use the plastic debris shield with the cut-off knife.
WARNING: Do not trim in any area where
there are strands of fencing wire. Wear
protective safety protection , Do not cut
where you cannot see what the cutting device is
cutting.
Cutting with a blade
(GBC-43)
SCYTHING WEEDS.
This consist of swinging the blade in a level arc.
1.
It can quickly clear areas of field grass and weeds.
Scything should not be used to cut large, tough
weeds or woody growths.
Scything can be done in both directions, or just
2.
in one way which results in the debris being thrown
away from you.Use the side of the blade that it is
rotating away from you. Tilt down the blade slightly
on this same side. You will be hit by some debris if
you scythe in both directions.
Cut only with the side of the blade that makes
3.
the debris is moving away from you.
If kickback occurs, the blade may be dull, or the
4.
material so thick and hard that you should use other
tool instead of this machine.
Do not force the blade to cut. Do not change
5.
the angle of cut after into the wood. Avoid using any
pressure or leverage which could cause the blade to
bind or crack .
WARNING: Do not cut with dull, cracked
or damaged meal blade.
Before cutting growth, inspect for
obstructions such as boulders, metal stakes
or strands of wire from broken fences. If an
obstruction can not be removed, mark its location
so that you can avoid it with the blade. Rocks and
metal will dull or damage a blade. Wire can catch
on the blade head and flap around or be thrown
Содержание GBC-43
