IVT AE-X12JR-N Скачать руководство пользователя страница 39

Страница: 39 / 68

AYXP12JHRN

3 – 17

Indoor
unit in
operation
Outdoor
unit in
complete
shutdown

-0

Wires between
units

Serial open-circuit

(1)

Check the wires between
units.

(1)

Connect stable power
supply.

(2)

Check voltage between
Nos. 1 and 2 on the
indoor/outdoor unit termi-
nal boards.

(2)

Replace the outdoor
unit control PCB
assembly.

Outdoor unit does
not turn on due to
erroneous wiring

(1)

Check the wires between
units.

(1)

Correct the wiring.

(2)

Check the outdoor unit
fuse.

(2)

Replace the fuse/out-
door unit control PCB
assembly.

(3)

Check 15-V, 13-V and 5-V
voltages on the PWB.
Check resistance between
IPM terminals.

(3)

Replace the outdoor
unit control PCB
assembly.

(4)

Check pins No. 5 and 7 of
connector CN3 of the out-
door unit fan motor for
short-circuit.

(4)

Replace the outdoor
unit fan motor.

(5)

Outdoor unit control PCB

(5)

Replace the outdoor
unit control PCB
board.

-0

Serial short-circuit

(1)

Check the wires between
units.

(1)

Correct the wiring.

-1

Serial erroneous wir-
ing

(1)

Check the wires between
units.

(1)

Correct the wiring.

Indoor/
outdoor
units in
complete
shutdown

-0

Indoor unit fan

Indoor unit fan error

(1)

Check the indoor fan
motor for proper rotating
operation.(Check fan
lock.)

(1)

Replace the indoor fan
motor.

(2)

Check the lead wire of the
indoor fan motor for open-
circuit.

(2)

Replace the indoor fan
motor.

(3)

Check CN1 of the indoor
unit fan motor for secure
installation.

(3)

Correct the installa-
tion of CN1 of the
indoor fan motor.

(4)

No abnormality found in
above inspections (1)
through (3).

(4)

Replace the indoor
unit control PWB.

Indoor/
outdoor
units in
operation

-0

Indoor unit con-
trol PCB

EEPROM data error

(EEPROM read data
error)

Replace the indoor
unit control PWB.

Indoor/
outdoor
units in
operation

-0

Panel

Panel open error

(1)

Caught of panel hook

(1)

Replace or adjustment
of the panel.

-1

Panel close error

(2)

Limit switch breakdown

(2)

Replace the limit
switch.

Indoor/
outdoor
units in
operation

Control and dis-
play PCB

Communication
error

(1)

Check for disconnected
connector between control
PCB and display PCB,
and open-circuit in lead
wires.

(1)

Insert connectors cor-
rectly, or replace con-
trol PWB.

(2)

Check that control PCB
outputs signals correctly.

(2)

Replace control PWB.

Status of

indoor/

outdoor

units

Indication

by LED1

on out-

door unit

Malfunction

No. dis-

played on

main unit

display sec-

tion *1

Content of diagnosis

Inspection location/method

Remedy

Main
cate-

gory

Sub-

cate-

gory

Main category

Sub-category

Содержание AE-X12JR-N





































































Результаты поиска

Содержание AE-X12JR-N

Отзывы:

Похожие инструкции для AE-X12JR-N

Бренды по названию

Популярные бренды

IVT AE-X12JR-N, Руководство по обслуживанию

Результаты поиска

Содержание AE-X12JR-N

Отзывы:

Похожие инструкции для AE-X12JR-N

Бренды по названию

Популярные бренды