IVT AE-X12JR-N Скачать руководство пользователя страница 25

Страница: 25 / 68

AYXP12JHRN

3 – 3

✩

1—The outdoor unit restarts four times before the indoor unit error is displayed (complete shutdown).

✩

2—A single error judgment results in the display of the indoor unit error (complete shutdown).

✩

3—The outdoor unit restarts eight times before the indoor unit error is displayed (complete shutdown).

[2] AIR CONDITIONER OPERATION IN THERMISTOR ERROR

1. Indoor unit

Compressor rota-
tion error (at 120

energizing)

Compressor stops if there is no
input of position detection signal
from compressor or input is
abnormal.

Compressor operat-
ing at 120

energizing

Operation OFF or ON

Yes

✩

Yes

Outdoor unit DC fan
error

Operation stops if there is no
input of rotation pulse signal from
outdoor unit fan motor for 30 sec-
onds.

When outdoor unit
fan is in operation

Operation OFF or ON

Yes

✩

Yes

PAM overvoltage
error

Compressor stops if DC voltage is
400 V or higher.

When in operation

Operation OFF or ON

Yes

✩

Yes

PAM clock error

When power source frequency
cannot be determined (at startup),
or when power source clock can-
not be detected for 1 continuous
second (at startup).

At compressor star-
tup, when in opera-
tion

Compressor contin-
ues operation with-
out stopping.

None

Yes

Item

Mode

Control opera-

tion

When resis-
tance is low

(temperature

judged higher

than actual)

Short-circuit

When resis-

tance is high
(temperature

judged lower

than actual)

Open-circuit

Room tempera-
ture thermistor
(TH1)

Auto

Operation mode
judgment

Cooling mode is
activated even if
room tempera-
ture is low.

Cooling mode is
activated in most
cases.

Heating mode is
activated even if
room tempera-
ture is high.

Heating mode is
always activated.

Cooling

Frequency control

Room becomes
too cold.

Air conditioner
operates in full
power even when
set temperature is
reached.

Room does not
become cool.

Compressor does
not operate.

Dehumidifying

Room tempera-
ture memory
Frequency control

Normal operation.

Room tempera-
ture is stored in
memory as
31.0

C, and com-

pressor does not
stop.

Normal operation.

Room tempera-
ture is stored in
memory as
18.5

C, and com-

pressor does not
operate.

Heating

Frequency control

Room does not
become warm.

Hot keep status
results immedi-
ately after opera-
tion starts.
Frequency does
not increase
above 30 Hz (40
Hz).

Room becomes
too warm.

Air conditioner
operates in full
power even when
set temperature is
reached.

Heat exchanger
thermistor (TH2)

Cooling
Dehumidifying

Freeze preven-
tion

Indoor unit evap-
orator may
freeze.

Compressor
stops occasion-
ally.

Compressor does
not operate.

Heating

Cold air preven-
tion

Cold air preven-
tion deactivates
too soon and cold
air discharges.

Compressor
operates at low
speed or stops,
and frequency
does not
increase.

Cold air preven-
tion deactivates
too slow.

Cold air preven-
tion does not
deactivate, and
indoor unit fan
does not rotate.

Function

Operation

Self-diagnosis

result display

Description

Detection period

Reset condition

Indoor

unit

error

display

Indoor

unit

Outdoor

unit

Содержание AE-X12JR-N





































































Результаты поиска

Содержание AE-X12JR-N

Отзывы:

Похожие инструкции для AE-X12JR-N

Бренды по названию

Популярные бренды

IVT AE-X12JR-N, Руководство по обслуживанию

Результаты поиска

Содержание AE-X12JR-N

Отзывы:

Похожие инструкции для AE-X12JR-N

Бренды по названию

Популярные бренды