background image

!

“Quick test to determine if electrical connections are done right”                                      

Note:

 

SkidWeigh weighing calibration function is not done yet at this stage. This  procedure is only to test if electrical 

connections of the system installation into the vehicle is done properly!                                                                                                                                                                    

After you have connected electrical power and pressure transducer cable you can “quickly” check the system operation. 
- Lower the forks to the ground                                                                                                                                           
- Turn On ignition switch                                                                                                                                                     
- Digital LCD display will be activated, showing software version and serial number                                                           
- Digital LCD display will show current date and time  

If the forks are lifted above the ground or perhaps engage the second stage to get some increased hydraulic pressure to 
test the sensor, LCD digital display will  show within few seconds  display some random load weight .  

(Example: 455) 

If the above test is valid than the system electrical connections are done right. The next procedure will be to calibrate the 
SkidWeigh weighing function and perhaps set the right time and date if current value is wrong.                                                                                        

   

 

Pressure transducer test procedure

                                                                                                                       

The ED3 SkidWeigh Plus system has provision that you can test the operation and working of the pressure transducer 
itself at any time. The pressure transducer fault could be in the wrong connection, loose  or broken connection of one of 
the 3 wires, faulty unit, etc. 
With forks on the ground  and LCD display 

must be showing date and time

, press

 F

 key and hold it until the LCD 

display shows 

ENTER FUNCTION. 

 Press number

 4

 to initiate pressure transducer self check.

LCD Display

Aug 28, 2010

12:20:23

LCD Display

PLEASE WEIGHT

WEIGHT = 455

LCD Display

ENTER NUMBER

LCD Display

4

Integrated Visual Data Technology Inc.   3439 Whilabout Terrace, Oakville, Ontario, Canada  L6L 0A7 

www.skidweigh.com

   

Содержание ED3-AT SkidWeigh Plus
















Отзывы: