manualshive.com logo in svg

ITW Simco-Ion Dual Phase+, Инструкция по установке и эксплуатации, Страница: 3 / 12

Поделиться
Скачать
ITW Simco-Ion Dual Phase+ Скачать руководство пользователя страница 3

1

Dual Phase+ Power Supply

5100636 Rev. F

1. SAFETY WARNINGS

NOTE

 – Statements Identified with a NOTE indicate precautions necessary 

to avoid potential equipment failure.

CAUTION

 – Statements identified with a CAUTION indicate potential 

safety hazards.

1.   This equipment must be correctly installed and properly maintained.  Adhere 

to the following cautions for safe installation and operation.

2.   Read instruction manual before operating or installing device.
3.   Qualified service personnel must do installation and repairs.
4.   Ground the frame of the machine on which the power supply and neutralizing 

bars are mounted.

5.   Disconnect supply voltage to power supply before connecting neutralizing bar 

to the high voltage terminal strip.

CAUTION

 – 

Electrical Shock Hazard

Do not touch bar when power supply is energized.
Disconnect supply voltage to power supply before connecting bar or 

performing any maintenance to the system.

CAUTION

 – 

Fire Hazard

Do not install or operate neutralizing bar in close proximity to any 

flammable solvents.

Содержание Simco-Ion Dual Phase+













Отзывы:

Нет отзывов