ITW 104020 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 28

ITW 104020 Скачать руководство пользователя страница 20

Instruction Manual

Page 20 of 28

Issue: 1.2

\\Argon\automotive_ftp\Manuals\Word Original\Pump Unit Maple 60 R1.2.docx

Maintenance – Section 5.1 - Assembly Procedure

Pump Assembly – Air Motor – Control Valve 192897

Main Valve (27) & exhaust manifold (28):-

1. Ensure all parts are free from

contamination especially the magnets
(52)

2. Lightly grease valve bore of housing (45)

and O-rings of spool assembly (53) Use
grease type #

3. Carefully insert the spool assembly into

the housing until centrally positioned.

4. Insert spacers (50) & bumpers (51) into

each end of the spool housing.

5. Insert magnets (52) into end cap (49)

then fit O-ring (41) lubricate with grease
type # and assemble into housing.

6. Position diaphragm (43) into QEV

cartridge (47) and fit into housing
(ensure transfer holes are inline &
ensure diaphragm is centrally located)

7. Fit exhaust plate (46) to manifold (28) with 6 off screws (42) using Loctite 222, tighten to

12Nm.

8. Fit 2 off O-rings (40) around QEV cartridges and fit the exhaust plate and manifold over

the QEV cartridges. Secure with 6 off screws (42) using Loctite 222, tighten to 12Nm.

9. Fit plug (44) is in position.

Assembly of Main Valve to Air Motor

1. Fit 2 off O-rings (3) and 4off O-rings (4) into air motor end plates (22)(23)

2. Lightly grease # 2 off cap head screws (14) and fit main valve assembly (27) onto the

end plates, tighten to 18Nm

3. Fit 2 off exhaust muffler (90) into 2 off exhaust adaptors (32)

«
...
18
19
20
21
22
...
»

Содержание 104020





























Отзывы:

Нет отзывов