manualshive.com logo in svg

ITW 104020, Инструкция по эксплуатации, Страница: 19 / 28

Поделиться
Скачать
ITW 104020 Скачать руководство пользователя страница 19

Instruction Manual 

 

 

 

Page 19 of 28 

Issue: 1.2

 

\\Argon\automotive_ftp\Manuals\Word Original\Pump Unit Maple 60 R1.2.docx 

Maintenance – Section 5.1 - Assembly Procedure 
 

Pump Assembly – Air Motor 

 

Ensure all parts are clean and degreased. 
1.  Push bearings (7) into end plates (22 & 23) and insert ‘O’ rings (8) into the large 

grooves, applying a light coating of grease type #. 

2.  Apply light coating of grease type # to the seal groove of the piston (24) and insert the 

‘O’ ring portion of the piston seal (5), apply a little more grease to the top of the ‘O’ ring. 
Carefully fit the seal strip into the piston groove (fit one half of the seal into the groove 
and then apply pressure to the o-ring seal already in the groove, and pull the remaining 
seal into the groove, being careful to avoid unduly stretching the  seal strip). 

3.  Insert grub screw (13) into one of the piston shafts (20) use Loctite studlock 2701 and 

tighten to 50Nm. Mount this through the piston (24) and screw on the other shaft (20) 
again using Loctite studlock 2701 and tighten to 100Nm. Clean off any residue of 
Loctite. 

4.  Lightly apply grease type # to the inside of the air motor cylinder (21), insert the piston 

and shaft sub-assembly into the cylinder at a 45° angle and turn the piston until it is 
inline with the cylinder. 

5.  Insert the cylinder end plate sub-assemblies over lightly greased # shafts and into the 

cylinder. Press parts lightly together, making sure that the Main Valve (27) mounting 
surfaces are inline. 

6.  Insert 5 off short tie rods(30) and 4off long tie rods(31) through the end plates. Fit 18 off 

washers (9) over the ends of the tie rods. Apply Loctite 243 to the LH end of the tie rods 
and add grease type # to the other end. Fit domed nuts (11) onto the LH loctited end 
and screw on as far as possible, screw on the remaining domed nuts and tighten in 
‘cross over’ sequence together to 22Nm. 

7.  Apply grease type # onto the shafts and gently push over the shaft seal (6), lips pointing 

inwards (Use Tool 502679 – or use tape to cover the grooves to allow seal to be pushed 
over), push the seal fully home into the end plate. Then fit the bellows retainer (26) over 
the shafts, smaller hole facing inwards.  

8.  Screw assembly tool (502681) onto the piston shaft (20). Using tool (502682) push the 

bellows (19) over the assembly tool until the bellows internal spigot locates into the shaft 
groove. (Using the tool prevents damage to the convolutions) 

9.  Smear a film of loctite 572 over the nose of the bellows then thread the 

nut (25) onto the bellows using tool (502682) to push against the nut 
ensuring the thread starts squarely. Grip the bellows and turn the nut 
with a 32 A/F spanner until positive resistance is felt. The distance 
between the nut and the first convolution should be 0 to 1mm. 

10.  Remove assembly tool (502681).  

11. Fit mounting brackets (29) to the end plates using 4off M10 cap head screws (12) and 

washers (10) tighten to 40Nm. Use Loctite 243 on threads. 

12. Install elbows (18) to the end plates, with hose (17). 
13. Lightly grease # threads and o-rings of pilot valves (16) and carefully screw into the end 

plates. Tighten to 8Nm (do not over tighten). 

Содержание 104020





























Отзывы:

Нет отзывов