background image

Technical Manual No. IOT4400F

Effective 8/31/2018

 

REV LEVEL B 

ITT Engineered Valves, LLC

 

33 C

ENTERVILLE

 R

OAD

 

L

ANCASTER

, PA   17603-2064 

T

EL

:  (717) 509-2200 

F

AX

:  (717) 509-2355 

www.engvalves.com 

INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS 

MODEL T4405F & T4406F & T4407F 

Skotch

 

Trifecta

 

VALVE SYSTEM 

WARNING 

Valves and valve actuators supplied by ITT Engineered Valves, LLC  are designed and 
manufactured using good workmanship and materials, and they meet the applicable industry 
standards. These valves are available with components of various materials, and they should be 
used only in services recommended herein or by a company valve engineer. Misapplication of 
the product may result in injuries or property damage. A selection of valve components of the 
proper material and consistent with the particular performance requirement is important for 
proper application. 

Examples of misapplication or misuse of products includes use in an application in which the 
pressure/temperature is exceeded or failure to maintain the equipment as recommended and use 
of products to handle caustic and/or hazardous substance when not design for that purpose. 

If valve exhibits any indication of leakage, do not operate. Isolate valve and either repair or 
replace. 

Содержание Skotch Trifecta T4405F










































Отзывы: