U.S.A.
Jabsco
1485 Dale Way, P.O. Box 2158
Costa Mesa, CA 92628-2158
Tel:
714.545.8251
Fax: 714.957.0609
UNITED KINGDOM
Jabsco
Bingley Road, Hoddesdon
Hertfordsire EN11 OBU
Tel:
+44 (0) 1992 450145
Fax: +44 (0) 1992 467132
CANADA
Fluid Products Canada
55 Royal Road
Guelph, Ontario N1H 1T1
Tel:
(519) 821.1900
Fax: (519) 821.2569
JAPAN
NHK Jabsco Company Ltd.
3-21-10, Shin-Yokohama
Kohoku-Ku, Yokohama, 222
Tel:
045.475.8906
Fax: 045.475.8908
GERMANY
Jabsco GmbH
Oststrasse 28
22840 Norderstedt
Tel:
+49-40-53 43 73 -0
Fax: +49-40-53 53 73 -11
THE PRODUCT DESCRIBED HEREIN IS
SUBJECT TO THE JABSCO ONE YEAR LIMITED
WARRANTY, WHICH IS AVAILABLE FOR YOUR
INSPECTION UPON REQUEST.
© Copyright 2000, ITT Industries Printed in U.S.A.
All Rights Reserved
Form: 43000-0369
Rev. 8/2000
DISASSEMBLY INSTRUCTIONS
1.
Remove end cover screws, end cover and gasket.
2.
Remove drain plug from body. Insert Allen wrench
through priming hole to loosen impeller set screw.
Withdraw impeller from shaft and body.
3.
Remove two motor mounting screws. Remove body
from motor.
4.
Press seal out of body towards motor flange end.
Check motor shaft for wear in seal lip area. Replace
motor if shaft is deeply grooved. This will only
happen, normally, if pump is run dry for extended
periods.
ASSEMBLY INSTRUCTIONS
1.
Support body on front face (impeller end). Lubricate
OD of seal and press into seal bore with lip facing
toward impeller until it bottoms firmly against
shoulder. Center seal retainer (concave side up)
in seal cavity and press firmly against seal using
11/16" dia. dowel.
2.
Position slinger on shaft 1/8" from motor face.
3.
Lubricate inside diameter of seal and shaft with
water pump grease. Install body to motor and secure
with two screws.
4.
Start set screw into impeller boss. Push impeller on
shaft with set screw centered on shaft flat, until
impeller contacts rear face of body. Pull impeller
away from body 1/32" and tighten set screw by
inserting Allen wrench through priming hole in body.
Turn impeller to make sure there is no metal contact.
5.
Install gasket, end cover and secure with four end
cover screws and lock washers.
6.
Install priming plug in body with a light coat of
sealant.
PARTS LIST
Part
Key
Description
Qty.
Number
1
Screw End Cover
4
91003-0230
2
Lock Washer
4
91602-0020
3
End Cover
1
18514-0000
4
Gasket
1
18516-0000
5
Impeller
1
18515-0000
6
Set Screw - Impeller
1
91083-0040
Part
Key
Description
Qty.
Number
7
Seal
1
1040-0001
8
Body - Volute
1
18513-0000
9
Plug
1
92650-0040
10
Screw - Motor Mtg. (3/kit)
1
98019-0020
11
Slinger
1
6342-0000
12
Motor - TENV 115/1/60
1
18753-0082
EXPLODED VIEW
