ITT Goulds Pumps JC Скачать руководство пользователя

Страница: 38 / 41

6 Spare Parts

6.1 Ordering spare parts

To ensure against possible long and costly downtime periods, especially on critical services, it is advisa-
ble to have spare parts on hand.

Parts orders will be handled most promptly if the following directions are followed.

Include pump model and size and its serial number as shown on the nameplate.

For each part required, include the name and part number.

State the quantity required for each part.

Provide complete shipping instructions.

6.1.1 Recommended spares

The following are recommended spare parts.

•

1 Suction Liner (100B)

•

1 Impeller (101)

•

1 Lantern Ring (105)

•

5 Packing Rings (106)

•

1 Thrust Bearing (112C)

•

1 Shaft Sleeve (126)

•

1 Radial Bearing (168C)

•

1 Parts Kit, see chart

Parts Kit Chart

Pump Size

Kit Number

1×1.5-8, 1.5×2-8, 2×3-8

520101

1×1.5-11, 1.5×2-11, 2×3-11

520102

1.5×2-14, 2×3-14

520103

3×4-11

520104

3×4-14, 4×6-14

520105

6×6-14 HS

520106

6×6-14 LS

520107

8×10-18

520108

10×12-22

520109

Parts Kits include thrust bearing locknut, lockwasher and snap ring, grease seals, and required
gaskets and/or O-rings.

6.2 Parts list

TYPICAL

Item

QTY/Pump

Part Name

Alternate Part Name

100

Casing

100B

Suction Liner

Suction Disc Liner

101

1(2)

Impeller

105

Lantern Ring

Seal Cage

6 Spare Parts

Model JC Installation, Operation and Maintenance Instructions

Содержание Goulds Pumps JC










































Результаты поиска

Содержание Goulds Pumps JC

Отзывы:

Похожие инструкции для Goulds Pumps JC

Бренды по названию

Популярные бренды

ITT Goulds Pumps JC, Дополнительные инструкции по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Goulds Pumps JC

Отзывы:

Похожие инструкции для Goulds Pumps JC

Бренды по названию

Популярные бренды